SCI和EI收录∣中国化工学会会刊

中国化学工程学报 ›› 2021, Vol. 34 ›› Issue (6): 1-11.DOI: 10.1016/j.cjche.2020.08.016

• Fluid Dynamics and Transport Phenomena •    下一篇

Spray and mixing characteristics of liquid jet in a tubular gas-liquid atomization mixer

Lingzhen Kong, Jiaqing Chen, Tian Lan, Huan Sun, Kuisheng Wang   

  1. 1 School of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617, China;
    2 Beijing Key Laboratory of Pipeline Critical Technology and Equipment for Deep Water Oil & Gas Development, Beijing 102617, China;
    3 College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China
  • 收稿日期:2020-07-05 修回日期:2020-08-14 出版日期:2021-06-28 发布日期:2021-08-30
  • 通讯作者: Jiaqing Chen
  • 基金资助:
    The financial supports from the National Natural Science Foundation of China (21808015) and the Project of Construction of Innovative Teams and Teacher Career Development for Universities and Colleges under Beijing Municipality (IDHT20170507) are gratefully acknowledged.

Spray and mixing characteristics of liquid jet in a tubular gas-liquid atomization mixer

Lingzhen Kong, Jiaqing Chen, Tian Lan, Huan Sun, Kuisheng Wang   

  1. 1 School of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617, China;
    2 Beijing Key Laboratory of Pipeline Critical Technology and Equipment for Deep Water Oil & Gas Development, Beijing 102617, China;
    3 College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China
  • Received:2020-07-05 Revised:2020-08-14 Online:2021-06-28 Published:2021-08-30
  • Contact: Jiaqing Chen
  • Supported by:
    The financial supports from the National Natural Science Foundation of China (21808015) and the Project of Construction of Innovative Teams and Teacher Career Development for Universities and Colleges under Beijing Municipality (IDHT20170507) are gratefully acknowledged.

摘要: For the design and optimization of a tubular gas-liquid atomization mixer, the atomization and mixing characteristics of liquid jet breakup in the limited tube space is a key problem. In this study, the primary breakup process of liquid jet column was analyzed by high-speed camera, then the droplet size and velocity distribution of atomized droplets were measured by Phase-Doppler anemometry (PDA). The hydrodynamic characteristics of gas flow in tubular gas-liquid atomization mixer were analyzed by computational fluid dynamics (CFD) numerical simulation. The results indicate that the liquid flow rate has little effect on the atomization droplet size and atomization pressure drop, and the gas flow rate is the main influence parameter. Under all experimental gas flow conditions, the liquid jet column undergoes a primary breakup process, forming larger liquid blocks and droplets. When the gas flow rate (Qg) is less than 127 m3·h-1, the secondary breakup of large liquid blocks and droplets does not occur in venturi throat region. The Sauter mean diameter (SMD) of droplets measured at the outlet is more than 140 μm, and the distribution is uneven. When Qg > 127 m3·h-1, the large liquid blocks and droplets have secondary breakup process at the throat region. The SMD of droplets measured at the outlet is less than 140 μm, and the distribution is uniform. When 127 < Qg < 162 m3·h-1, the secondary breakup mode of droplets is bag breakup or pouch breakup. When 181 < Qg < 216 m3·h-1, the secondary breakup mode of droplets is shear breakup or catastrophic breakup. In order to ensure efficient atomization and mixing, the throat gas velocity of the tubular atomization mixer should be designed to be about 51 m·s-1 under the lowest operating flow rate. The pressure drop of the tubular atomization mixer increases linearly with the square of gas velocity, and the resistance coefficient is about 2.55 in single-phase flow condition and 2.73 in gas-liquid atomization condition.

关键词: Atomization mixing, Liquid jet, Primary breakup, Droplet breakup, Droplet size

Abstract: For the design and optimization of a tubular gas-liquid atomization mixer, the atomization and mixing characteristics of liquid jet breakup in the limited tube space is a key problem. In this study, the primary breakup process of liquid jet column was analyzed by high-speed camera, then the droplet size and velocity distribution of atomized droplets were measured by Phase-Doppler anemometry (PDA). The hydrodynamic characteristics of gas flow in tubular gas-liquid atomization mixer were analyzed by computational fluid dynamics (CFD) numerical simulation. The results indicate that the liquid flow rate has little effect on the atomization droplet size and atomization pressure drop, and the gas flow rate is the main influence parameter. Under all experimental gas flow conditions, the liquid jet column undergoes a primary breakup process, forming larger liquid blocks and droplets. When the gas flow rate (Qg) is less than 127 m3·h-1, the secondary breakup of large liquid blocks and droplets does not occur in venturi throat region. The Sauter mean diameter (SMD) of droplets measured at the outlet is more than 140 μm, and the distribution is uneven. When Qg > 127 m3·h-1, the large liquid blocks and droplets have secondary breakup process at the throat region. The SMD of droplets measured at the outlet is less than 140 μm, and the distribution is uniform. When 127 < Qg < 162 m3·h-1, the secondary breakup mode of droplets is bag breakup or pouch breakup. When 181 < Qg < 216 m3·h-1, the secondary breakup mode of droplets is shear breakup or catastrophic breakup. In order to ensure efficient atomization and mixing, the throat gas velocity of the tubular atomization mixer should be designed to be about 51 m·s-1 under the lowest operating flow rate. The pressure drop of the tubular atomization mixer increases linearly with the square of gas velocity, and the resistance coefficient is about 2.55 in single-phase flow condition and 2.73 in gas-liquid atomization condition.

Key words: Atomization mixing, Liquid jet, Primary breakup, Droplet breakup, Droplet size