A New Tuning Method for Two-Degree-of-Freedom Internal Model Control under Parametric Uncertainty

doi:10.1016/S1004-9541(13)60564-9

Chin.J.Chem.Eng. ›› 2013, Vol. 21 ›› Issue (9): 1030-1037.DOI: 10.1016/S1004-9541(13)60564-9

Previous Articles Next Articles

A New Tuning Method for Two-Degree-of-Freedom Internal Model Control under Parametric Uncertainty

Juwari Purwo sutikno^1,2, Badhrulhisham Abdul aziz¹, Chin Sim yee¹, Rosbi Mamat³

1 Process System Engineering Group, Faculty of Chemical and Natural Resources Engineering Universiti Malaysia Pahang, Lebuhraya Tun Razak Gambang, Kuantan 26300, Malaysia;
2 Process Design and Control Laboratory, Chemical Engineering Department, Institut Teknologi Sepuluh Nopember Surabaya, Kampus ITS Sukolilo, Surabaya 60111, Indonesia;
3 Faculty of Electrical Engineering, Universiti Teknologi Malaysia, Skudai, Johor 81310, Malaysia

Received:2012-02-08 Revised:2012-09-22 Online:2013-10-01 Published:2013-09-28
Contact: Juwari Purwo sutikno
Supported by:
Supported by Postgraduate Fellowship of UMP, Fundamental Research Grant Scheme of Malaysia (GRS070120) and Joint Research Grant between Universiti Malaysia Pahang (UMP) and Institut Teknologi Sepuluh Nopember (ITS) Surabaya

A New Tuning Method for Two-Degree-of-Freedom Internal Model Control under Parametric Uncertainty

Juwari Purwo sutikno^1,2, Badhrulhisham Abdul aziz¹, Chin Sim yee¹, Rosbi Mamat³

1 Process System Engineering Group, Faculty of Chemical and Natural Resources Engineering Universiti Malaysia Pahang, Lebuhraya Tun Razak Gambang, Kuantan 26300, Malaysia;
2 Process Design and Control Laboratory, Chemical Engineering Department, Institut Teknologi Sepuluh Nopember Surabaya, Kampus ITS Sukolilo, Surabaya 60111, Indonesia;
3 Faculty of Electrical Engineering, Universiti Teknologi Malaysia, Skudai, Johor 81310, Malaysia

通讯作者: Juwari Purwo sutikno
基金资助:
Supported by Postgraduate Fellowship of UMP, Fundamental Research Grant Scheme of Malaysia (GRS070120) and Joint Research Grant between Universiti Malaysia Pahang (UMP) and Institut Teknologi Sepuluh Nopember (ITS) Surabaya

Abstract

Abstract: Internal model control (IMC) yields very good performance for set point tracking, but gives sluggish response for disturbance rejection problem. A two-degree-of-freedom IMC (2DOF-IMC) has been developed to overcome the weakness. However, the setting of parameter becomes a complicated matter if there is an uncertainty model. The present study proposes a new tuning method for the controller. The proposed tuning method consists of three steps. Firstly, the worst case of the model uncertainty is determined. Secondly, the parameter of set point controller using maximum peak (Mp) criteria is specified, and finally, the parameter of the disturbance rejection controller using gain margin (GM) criteria is obtained. The proposed method is denoted as Mp-GM tuning method. The effectiveness of Mp-GM tuning method has evaluated and compared with IMC-controller tuning program (IMCTUNE) as bench mark. The evaluation and comparison have been done through the simulation on a number of first order plus dead time (FOPDT) and higher order processes. The FOPDT process tested includes processes with controllability ratio in the range 0.7 to 2.5. The higher processes include second order with underdamped and third order with nonminimum phase processes. Although the two of higher order processes are considered as difficult processes, the proposed Mp-GM tuning method are able to obtain the good controller parameter even under process uncertainties.

Key words: tuning 2DOF-IMC, model uncertainty, dead time process, Mp-GM tuning, IMCTUNE

摘要： Internal model control (IMC) yields very good performance for set point tracking, but gives sluggish response for disturbance rejection problem. A two-degree-of-freedom IMC (2DOF-IMC) has been developed to overcome the weakness. However, the setting of parameter becomes a complicated matter if there is an uncertainty model. The present study proposes a new tuning method for the controller. The proposed tuning method consists of three steps. Firstly, the worst case of the model uncertainty is determined. Secondly, the parameter of set point controller using maximum peak (Mp) criteria is specified, and finally, the parameter of the disturbance rejection controller using gain margin (GM) criteria is obtained. The proposed method is denoted as Mp-GM tuning method. The effectiveness of Mp-GM tuning method has evaluated and compared with IMC-controller tuning program (IMCTUNE) as bench mark. The evaluation and comparison have been done through the simulation on a number of first order plus dead time (FOPDT) and higher order processes. The FOPDT process tested includes processes with controllability ratio in the range 0.7 to 2.5. The higher processes include second order with underdamped and third order with nonminimum phase processes. Although the two of higher order processes are considered as difficult processes, the proposed Mp-GM tuning method are able to obtain the good controller parameter even under process uncertainties.

关键词: tuning 2DOF-IMC, model uncertainty, dead time process, Mp-GM tuning, IMCTUNE

Juwari Purwo sutikno, Badhrulhisham Abdul aziz, Chin Sim yee, Rosbi Mamat. A New Tuning Method for Two-Degree-of-Freedom Internal Model Control under Parametric Uncertainty[J]. Chin.J.Chem.Eng., 2013, 21(9): 1030-1037.

References

1 Garcia, C.E., Morari, M., “Internal model control. A unifying review and some new results”, Ind. & Eng. Chem. Pro. Des. and Dev., 21 (2), 308-323 (1982).

2 Morari, M., Zafiriou, E., “Robust Process Control”, Englewood Cliffs, Prentice Hall, New Jersey (1989).

3 Rivera, D.E., Morari, M., Skogestad, S., “Internal model control: PID controller design”, Ind. & Eng. Chem. Pro. Des. and Dev., 25 (1), 252-265 (1986).

4 Brosilow, C., Joseph, B., “Techniques of model-based control”, In: Prentice Hall International Series in the Physical and Chemical Engineering Science, Prentice Hall PTR, New Jersey (2001).

5 Smith O, J., “A controller to overcome dead time”, ISA J. 6 (2), 28-33 (1959).

6 Bin, H, Pingyou, Z., Jun, L., “Multi-loop internal model controller design based on a dynamic PLS framework”, Chin. J. Chem. Eng., 18 (2), 277-285 (2010).

7 Laughlin, D.L., Jordan, K.G., Morari, M., “Internal model control and process uncertainty: Mapping uncertainty regions for SISO controller design”, Int. J. Cont., 44 (6), 1675-1698 (1986).

8 Liu, K., Shimizu, T., Inagaki, M., Ohkawa, A., “New tuning method for IMC controller”, J. Chem. Eng. Jpn., 31 (3), 320-324 (1998).

9 Stryczek, K., Laiseca, M., Brosilow, C., Leitman, M.G., “Tuning and design of single-input, single-output control systems for parametric uncertainty”, AIChE J., 46 (8), 1616-1631 (2000).

10 Stryczek, K., “Mp-tuning of internal model control systems under parametric uncertainty”, Ph.D. Thesis, Case Western Reserve University, USA (1996).

11 Stryczek, K., Dong, J., Kumsaen, T., Brosilow, C.B., “IMC-controller tuning program (IMCTUNE)”, 10th edition, Prentice Hall, New Jersey (2002).

12 Chia, T.L., Lefkowitz, I., “Internal model-based control for integrating processes”, ISA T., 49 (4), 519-527 (2010).

13 Liu, T., Gao, F., “Enhanced IMC design of load disturbance rejection for integrating and unstable processes with slow dynamics”, ISA T., 50 (2), 239-248 (2011).

14 Tan, W., “Analysis and design of a double two-degree-of-freedom control scheme”, ISA T., 49 (3), 311-317 (2010).

15 Tan, W., Marquez, H.J., Chen, T., “IMC design for unstable processes with time delays” J. Proc. Cont., 13 (3), 203-213 (2003).

16 Wang, R., Watanabe, K., “Three-degree-of-freedom internal model control for unstable process”, In: SICE Annual Conference, Kagawa University, Japan (2007).

17 Cheng, C., Chiu, M.S., “Adaptive IMC controller design for nonlinear process control”, Chem. Eng. Res. and Des., 85 (2), 234-244 (2007).

18 Ganeshreddy Kalmukale, A., Chiu, M.S., Luis, P., Antonio, E., “Data-based internal model controller design for a class of nonlinear systems”, Comp. Aid. Chem. Eng., 1411-1416 (2005).

19 Toivonen, H.T., Sandström, K.V., Nyström, R.H., “Internal model control of nonlinear systems described by velocity-based linearizations”, J. Proc. Cont., 13 (3), 215-224 (2003).

20 Levine, W.S., “The Control Handbook”, CRC Press, Boca Raton (1995).

21 Kuo, B.C., “Automatic control systems”, 7th edition, Englewood Cliffs, Prentice Hall, New Jersey (1995).

22 Seborg, D.E., Edgar, T.F., Mellicamp, D.A., “Process dynamic and control”, 2nd edition, John Wiley & Sons, USA (2004).

23 Astrom, K.J., Panagopoulos, H., HÄGglund, T., “Design of PI controllers based on non-convex optimization”, Automatica., 34 (5), 585-601 (1998).

24 Hang, C.C., Ho, W.K., Cao, L.S., “A comparison of two design methods for PID controllers”, ISA T., 33 (2), 147-151 (1994).

25 Ho, W.K., Lim, K.W., Xu, W., “Optimal gain and phase margin tuning for PID Controllers”, Automatica., 34 (8), 1009-1014 (1998).

26 Wang, Q.G., Fung, H.W., Zhang, Y., “PID tuning with exact gain and phase margins”, ISA T., 38 (3), 243-249 (1999).

27 Yaniv, O., Nagurka, M., “Design of PID controllers satisfying gain margin and sensitivity constraints on a set of plants”, Automatica., 40 (1), 111-116 (2004).

28 Marlin, T.E., “Process Control: Designing Processes and Control Systems for Dynamic Performance”, Chemical Engineering Series, 2nd edition, McGrawHill, Boston (2000).

29 Chang, D.M., Yu, C.C., Chien, I.L., “Coordinate control of blending systems”, IEEE Trans. on Cont. Sys. Tech., 6 (4), 495-506 (1998).

30 Vilanova, R., “IMC based robust PID design: Tuning guidelines and automatic tuning”, J. Proc. Cont., 18 (1), 61-70 (2008).

31 Skogestad, S. “Simple analytic rules for model reduction and PID controller tuning”, J. Proc. Cont., 13 (4), 291-309 (2003).

32 Panda, R.C., Yu, C.C., Huang, H.P., “PID tuning rules for SOPDT systems: Review and some new results” ISA T., 43 (2), 283-295 (2004).

A New Tuning Method for Two-Degree-of-Freedom Internal Model Control under Parametric Uncertainty

A New Tuning Method for Two-Degree-of-Freedom Internal Model Control under Parametric Uncertainty

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 0

Recommended Articles

Metrics

Comments