Modeling and simulation of material distribution in the sequential co-injection molding process

doi:10.1016/j.cjche.2021.01.005

Abstract

Abstract: In co-injection molding, the properties and distribution of polymers will affect the application of products. The focus of this work is to investigate the effect of molding parameters on the skin/core material distribution based on three-dimensional (3-D) flow and heat transfer model for the sequential co-injection molding process, and the flow behaviors and material distributions of skin and core melts inside a slightly complex cavity (dog-bone shaped cavity) are predicted numerically. The governing equations of fluids in mold are solved by finite volume method and Semi-Implicit Method for Pressure Linked Equations (SIMPLE) algorithm on collocated meshes, and the domain extension technique is employed in numerical method for this cavity to assure that the numerical algorithm is implemented successfully. The level set transport equation which is used to trace the free surfaces in co-injection molding is discretized and solved by the 5th-order Weighted Essentially Non-Oscillatory (WENO) scheme in space and 3rd-order Total Variation Diminishing Runger-Kutta (TVD-R-K) scheme in time respectively. Numerical simulations are conducted under various volume fraction of core melt, skin and core melt temperatures, skin and core melt flow rates. The predicted results of material distribution in length, width and thickness directions are in close agreement with the experimental results, which indicate that volume fraction of core melt, core melt temperature and core melt flow rate are principal factors that have a significant influence on material distribution. Numerical results demonstrate the effectiveness of the 3-D model and the corresponding numerical methods in this work, which can be used to predict the melt flow behaviors and material distribution in the process of sequential co-injection molding.

Key words: Co-injection molding, Finite volume method, Simulation, Level set, Material distribution

摘要： In co-injection molding, the properties and distribution of polymers will affect the application of products. The focus of this work is to investigate the effect of molding parameters on the skin/core material distribution based on three-dimensional (3-D) flow and heat transfer model for the sequential co-injection molding process, and the flow behaviors and material distributions of skin and core melts inside a slightly complex cavity (dog-bone shaped cavity) are predicted numerically. The governing equations of fluids in mold are solved by finite volume method and Semi-Implicit Method for Pressure Linked Equations (SIMPLE) algorithm on collocated meshes, and the domain extension technique is employed in numerical method for this cavity to assure that the numerical algorithm is implemented successfully. The level set transport equation which is used to trace the free surfaces in co-injection molding is discretized and solved by the 5th-order Weighted Essentially Non-Oscillatory (WENO) scheme in space and 3rd-order Total Variation Diminishing Runger-Kutta (TVD-R-K) scheme in time respectively. Numerical simulations are conducted under various volume fraction of core melt, skin and core melt temperatures, skin and core melt flow rates. The predicted results of material distribution in length, width and thickness directions are in close agreement with the experimental results, which indicate that volume fraction of core melt, core melt temperature and core melt flow rate are principal factors that have a significant influence on material distribution. Numerical results demonstrate the effectiveness of the 3-D model and the corresponding numerical methods in this work, which can be used to predict the melt flow behaviors and material distribution in the process of sequential co-injection molding.

关键词: Co-injection molding, Finite volume method, Simulation, Level set, Material distribution

Qingsheng Liu, Youqiong Liu, Chuntao Jiang. Modeling and simulation of material distribution in the sequential co-injection molding process[J]. Chinese Journal of Chemical Engineering, 2022, 44(4): 507-520.

Qingsheng Liu, Youqiong Liu, Chuntao Jiang. Modeling and simulation of material distribution in the sequential co-injection molding process[J]. 中国化学工程学报, 2022, 44(4): 507-520.

References

[1] F. Ilinca, J.F. Hétu, A. Derdouri, Numerical investigation of the flow front behavior in the co-injection moulding process, Int. J. Num. Meth. Fl. 50(12) (2006) 1445-1460
[2] Q. Liu, J. Ouyang, W. Zhou, X. Xu, L. Zhang, Numerical simulation of the sequential coinjection molding process based on level set method, Polym. Eng. Sci. 55(8) (2015) 1707-1719
[3] Q. Liu, J. Ouyang, W. Li, X. Zhuang, C. Jiang, Three-dimensional modelling and simulation of sequential co-injection molding with application to a toothbrush handle, Can. J. Chem. Eng. 94(2) (2016) 382-390
[4] R. Seldén, Co-injection molding:Effect of processing on material distribution and mechanical properties of a sandwich molded plate, Polym. Eng. Sci. 40(5) (2000) 1165-1176
[5] F.B.Vangosa, Effects of process parameters on the skin/core distribution in co-injection:Experiments and simulations using a simple geometry, Polym-Plast. Technol. 50(13) (2011) 1314-1322
[6] G.L. Wang, Y.G. Zhou, S.J. Wang, J.B. Chen, X.L. Zhang, S. Lu, Cylindritic structures of isotactic polypropylene molded by sequential co-injection molding, J. Polym. Res. 20(212) (2013) 1-11
[7] D. Watanabe, U.S. Ishiaku, T. Nagaoka, K. Tomari, H. Hamada, Flow behavior of sandwich injection molding in sequential and simultaneous injection, Int. Polym. Proc. 18(2) (2003) 199-203
[8] D. Watanabe, U.S. Ishiaku, T. Nagaoka, K. Tomari, H. Hamada, The flow behavior of core material and breakthrough phenomenon in sandwich injection molding. Part I:Dependence on viscosity and injection speed of skin/core materials, Int. Polym. Proc. 18(4) (2003) 398-404
[9] T. Nagaoka, U.S. Ishiaku, T. Tomari, H. Hamada, S. Takashima, Effect of molding parameters on the properties of PP/PP sandwich injection moldings, Polym. Test. 24(8) (2005) 1062-1070
[10] M. Kadota, M. Cakmak, H. Hamada, Structural hierarchy developed in co-injection molded polystyrene/polypropylene parts, Polymer. 40(11) (1999) 3119-3145
[11] W.M. Yang, H. Yokoi, Visual analysis of the flow behavior of core material in a fork portion of plastic sandwich injection molding, Polym. Test. 22(1) (2003) 37-43
[12] S. Patcharaphun, G. Mennig, Simulation and experimental investigations of material distribution in the sandwich injection molding process, Polym-Plast. Technol. 45(6) (2006) 759-768
[13] G. Schlatter, J.F. Agassant, A. Davidoff, Vincent, M. An unsteady multifluid flow model:Application to sandwich injection molding process, Polym. Eng. Sci. 39(1) (1999) 78-88
[14] S.C. Chen, N.T. Chen, K.S. Hsu, K.F. Hsu, Study of polymer melt flow in sequential injection molding process, AIChE. J. 42(6) (1996) 1706-1714
[15] N.H. Kim, A.I. Isayev, Birefringence and interface in sequential co-injection molding of amorphous polymers:Simulation and experiment, Polym. Eng. Sci. 55(1) (2015) 88-106
[16] C.T. Li, A.I. Isayev, Interface development and encapsulation in simultaneous coinjection molding. I. Two-dimensional modeling and formulation, J. Appl. Polym. Sci. 88(9) (2003) 2300-2309
[17] C.T. Li, D.J. Lee, A.I. Isayev, Interface development and encapsulation in simultaneous coinjection molding of disk. II. Two-dimensional simulation and experiment, J. Appl. Polym. Sci. 88(9) (2003) 2310-2318
[18] Q. Liu, J. Ouyang, Z. Liu, W. Li, Visualization and simulation of filling process of simultaneous co-injection molding based on level set method, J. Polym. Eng. 35(9) (2015) 813-827
[19] F. Ilinca, J.F. Hétu, Three-dimensional simulation of multi-material injection molding:Application to gas-assisted and co-injection molding, Polym. Eng. Sci. 43(7) (2003) 1415-1427
[20] C.T. Huang, C.P. Lin, S.P. Sun, S.C. Tseng, R.Y. Chang, Numerical simulation and experimental study on physical mechanism in multiple component moulding, Int. J. Mater. Prod. Tec. 52(1-2) (2016) 118-142
[21] C.T. Huang, Numerical visualization and optimization on the core penetration in multi-cavity co-injection molding with a bifurcation runner structure, Int. J. Adv. Manuf. Techol. 92(5-8) (2017) 2545-2557
[22] L.B. Chen, Y.H. Huang, L. Liu, X. Zhao, Z.Y. Liu, W. Yang, M.B. Yang, Formation mechanism of hierarchically crystalline structures under coupled external fields in multi-melt mult-injection molding:Simulation and experiment, Compos. Part B-Eng. 188 (2020) 107770
[23] Q. Liu, Y. Liu, C. Jiang, S. Zheng, Modeling and simulation of weld line location and properties during injection molding based on viscoelastic constitutive equation, Rheol. Acta. 59(3) (2020) 109-121
[24] S. Osher, J.A. Sethian, Fronts propagating with curvature dependent speed:Algorithms based on Hamilton-Jacobi formulations, J. Comput. Phys. 79(1) (1988) 12-49
[25] S. Osher, R.P. Fedkiw, Level set methods:An overview and some recent results. J. Comput. Phys. 169(2) (2001) 463-502
[26] H.M. Zhou, Computer Modeling for Injection Molding:Simulation, Optimization, and Control, John Wiley & Sons, Inc., Singapore, 2013
[27] Q. Li, J. Ouyang, B. Yang, T. Jiang, Modelling and simulation of moving interfaces in gas-assisted injection moulding process. Appl. Math. Model. 35(1) (2011) 257-275
[28] H. Zhou, B. Yan, Y. Zhang, 3D filling simulation of injection molding based on the PG method, J. Mater. Process. Tech. 204(1-3) (2008) 475-480
[29] C.W. Shu, S. Osher, Efficient implementation of essentially non-oscillatory shock- capturing schemes, J. Comput. Phys. 77(2) (1988) 439-471
[30] A.T. Prata, E.M. Sparrow, Heat transfer and fluid flow characteristics for an annulus of periodically varying cross section, Numer. Heat. Transfer. 7(3) (1984) 285-304
[31] A. Korichi, L. Oufer, G. Polidori, Heat transfer enhancement in self-sustained oscillatory flow in a grooved channel with oblique plates, Int. J. Heat. Mass. Tran. 52(5-6) (2009) 1138-1148
[32] Q. Li, J. Ouyang, G. Wu, X. Xu, Numerical simulation of melt filling and gas penetration in gas assisted injection molding, CMES-Comp. Model. Eng. 82(3) (2011) 215-232
[33] X. Chen, P. Han, A note on the solution of conjugate heat transfer problems using SIMPLE-like algorithms, Int. J. Heat. Fluid. Fl. 21(4) (2000) 463-467
[34] J.H. Nie, B.F. Armaly, Three-dimensional convective flow adjacent to backward-facing step-effects of step height, Int. J. Heat. Mass. Tran. 45(12) (2002) 2431-2438