Numerical study of n-heptane/benzene separation by thermal diffusion column

doi:10.1016/j.cjche.2018.10.004

Abstract

Abstract: In this article, numerical simulations are performed to investigate the performance of the thermal diffusion column for the separation of n-heptane/benzene mixture. The present work tried to optimize column by analyzing significant parameters such as feed flow rate, temperature and cut. In order to obtain the hydrodynamic and temperature and mass distribution inside thermal diffusion column, computational fluid dynamic (CFD) method is applied to solve the Navier-Stocks equations. Numerical simulations are conducted to study the main parameters in both stationary and time-dependent conditions. By using the separation work unit as a function of cut, the optimal cut for maximum SWU occurs within a limited range of 0.47-0.5 for feed rate between 0.5 and 4·g min^-1. Our findings reveal that the optimum feed rate in the range of optimum cut is about 1 g min^-1. In transient study, results show that the best cut for reaching to steady-state condition is θ=0.5.

Key words: Thermal diffusion column (TDC), Computational fluid dynamic, Separative work unit, n-Heptane/benzene separation

摘要： In this article, numerical simulations are performed to investigate the performance of the thermal diffusion column for the separation of n-heptane/benzene mixture. The present work tried to optimize column by analyzing significant parameters such as feed flow rate, temperature and cut. In order to obtain the hydrodynamic and temperature and mass distribution inside thermal diffusion column, computational fluid dynamic (CFD) method is applied to solve the Navier-Stocks equations. Numerical simulations are conducted to study the main parameters in both stationary and time-dependent conditions. By using the separation work unit as a function of cut, the optimal cut for maximum SWU occurs within a limited range of 0.47-0.5 for feed rate between 0.5 and 4·g min^-1. Our findings reveal that the optimum feed rate in the range of optimum cut is about 1 g min^-1. In transient study, results show that the best cut for reaching to steady-state condition is θ=0.5.

关键词: Thermal diffusion column (TDC), Computational fluid dynamic, Separative work unit, n-Heptane/benzene separation

Neda Hashemipour, Javad Karimi-Sabet, Kazem Motahari, Saeed Mahruz Monfared, Younes Amini, Mohammad Ali Moosavian. Numerical study of n-heptane/benzene separation by thermal diffusion column[J]. Chinese Journal of Chemical Engineering, 2019, 27(8): 1745-1755.

References

[1] A.L. Jones, E.C. Milberger, Separation of organic liquid mixtures by thermal diffusion, Ind. Eng. Chem. 45(1953) 2689-2696.
[2] C. Ludwig, Sitzungsber. Akad. Wiss. Wien, Math, Naturwiss. Kl 20(1856) 1856.
[3] H.-M. Yeh, C.-D. Ho, L.-Y. Chen, The improvement of thermal diffusion performance in the modified Frazier scheme by increasing the column heights at a constant ratio, Sep. Sci. Technol. 50(2015) 17-25.
[4] E. Karbasi, J. Karimi-Sabet, J. Mohammadi-Rovshandeh, M.A. Moosavian, H. Ahadi, Y. Amini, Experimental and numerical study of air-gap membrane distillation (AGMD):Novel AGMD module for Oxygen-18 stable isotope enrichment, Chem. Eng. J. 322(2017) 667-678.
[5] Y. Amini, J. Karimi-Sabet, M. Nasr Esfahany, Experimental and numerical study of multiphase flow in new wire gauze with high capacity structured packing, Chem. Eng. Process. Process Intensif. 108(2016) 35-43.
[6] J. Bardeen, Concentration of isotopes by thermal diffusion:Rate of approach to equilibrium, Phys. Rev. 57(1940) 35.
[7] Y. Amini, J. Karimi-Sabet, M.N. Esfahany, Experimental and numerical simulation of dry pressure drop in high-capacity structured packings, Chem. Eng. Technol. 39(2016) 1161-1170.
[8] R. Moradi, J. Karimi-Sabet, M. Shariaty-Niassar, Y. Amini, Air gap membrane distillation for enrichment of H₂₁₈O isotopomers in natural water using poly (vinylidene fluoride) nanofibrous membrane, Chem. Eng. Process. Process Intensif. 100(2016) 26-36.
[9] W.H. Furry, R.C. Jones, Isotope separation by thermal diffusion:the cylindrical case, Phys. Rev. 69(1946) 459.
[10] R. Simon, Performance of a hot wire Clusius and Dickel column, Phys. Rev. 69(1946) 596.
[11] I. Bindeman, C. Lundstrom, C. Bopp, F. Huang, Stable isotope fractionation by thermal diffusion through partially molten wet and dry silicate rocks, Earth Planet. Sci. Lett. 365(2013) 51-62.
[12] H.-M. Yeh, C.C. Hsu, Recovery of deuterium from H-D gas mixture by thermal diffusion in the Frazier scheme, Prog. Nucl. Energy 53(2011) 645-650.
[13] H.-M. Yeh, Enrichment of heavy water in flat-plate thermal diffusion columns inclined for improved performance, Sep. Purif. Technol. 26(2002) 227-236.
[14] D. Reith, F. Müller-Plathe, On the nature of thermal diffusion in binary Lennard-Jones liquids, J. Chem. Phys. 112(2000) 2436-2443.
[15] I.I. Ryzhkov, I.V. Stepanova, On thermal diffusion separation in binary mixtures with variable transport coefficients, Int. J. Heat Mass Transf. 86(2015) 268-276.
[16] D. Stadelmaier, W. Kohler, Thermal diffusion of dilute polymer solutions:The role of chain flexibility and the effective segment size, Macromolecules 42(2009) 9147-9152.
[17] F.M. Richter, E.B. Watson, R.A. Mendybaev, F.-Z. Teng, P.E. Janney, Magnesium isotope fractionation in silicate melts by chemical and thermal diffusion, Geochim. Cosmochim. Acta 72(2008) 206-220.
[18] P. Foroozan Jahromi, J. Karimi-Sabet, Y. Amini, Ion-pair extraction-reaction of calcium using Y-shaped microfluidic junctions:An optimized separation approach, Chem. Eng. J. 334(2018) 2603-2615.
[19] W.M. Rutherford, Liquid-phase thermal diffusion isotope separation apparatus and method having tapered column, Google Patents, 1988.
[20] P. Foroozan Jahromi, J. Karimi-Sabet, Y. Amini, H. Fadaei, Pressure-driven liquid-liquid separation in Y-shaped microfluidic junctions, Chem. Eng. J. 328(2017) 1075-1086.
[21] N. Cox, P. Drapala, B.F. Finlayson, Transport limitations in thermal diffusion, Ph D Thesis, University of Washingtan, USA, 2007.
[22] P. Blanco, M.M. Bou-Ali, J.K. Platten, D.A. de Mezquia, J.A. Madariaga, C. Santamaría, Thermodiffusion coefficients of binary and ternary hydrocarbon mixtures, J. Chem. Phys. 132(2010) 114506.
[23] H.-M. Yeh, C.-C. Hsu, Separation of deuterium from H-D gas mixture by thermal diffusion in the devices of multi concentric-tube columns with total sum of column heights fixed, J. Nucl. Mater. 406(2010) 317-322.
[24] W. Rutherford, Separation of highly enriched 34S by liquid phase thermal diffusion of carbon disulfide, Ind. Eng. Chem. Process Des. Dev. 17(1978) 77-81.
[25] H.-M. Yeh, Improvement in recovery of deuterium from water-isotopes mixture in inclined thermal-diffusion columns, Int. J. Hydrog. Energy 28(2003) 873-879.
[26] I. Yamamoto, T. Baba, A. Kanagawa, Measurement of separative characteristics of thermal diffusion column for argon isotope separation, J. Nucl. Sci. Technol. 24(1987) 565-572.
[27] B. Hafskjold, T. Ikeshoji, S.K. Ratkje, On the molecular mechanism of thermal diffusion in liquids, Mol. Phys. 80(1993) 1389-1412.
[28] P. Polyakov, M. Zhang, F. Müller-Plathe, S. Wiegand, Thermal diffusion measurements and simulations of binary mixtures of spherical molecules, J. Chem. Phys. 127(2007) 014502.
[29] N. Ota, D.A. Agard, Intramolecular signaling pathways revealed by modeling anisotropic thermal diffusion, J. Mol. Biol. 351(2005) 345-354.
[30] M. Eslamian, Advances in thermodiffusion and thermophoresis (Soret effect) in liquid mixtures, Front. Heat Mass Transf. 2(2012).
[31] N. Hashemipour, J. Karimi-Sabet, K. Motahari, S. Mahruz Monfared, Y. Amini, M.A. Moosavian, Experimental and simulation investigation on separation of binary hydrocarbon mixture by thermogravitational column, J. Mol. Liq. 268(2018) 791-806.
[32] Y. Amini, M. Mokhtari, M. Haghshenasfard, M.B. Gerdroodbary, Heat transfer of swirling impinging jets ejected from nozzles with twisted tapes utilizing CFD technique, Case Stud. Therm. Eng. 6(2015) 104-115.
[33] H. Yamakawa, K. Matsumoto, Y. Enokida, I. Yamamoto, Numerical analysis of dynamic behavior at start-up of the thermal diffusion column for hydrogen isotope separation, J. Nucl. Sci. Technol. 36(1999) 198-203.
[34] H. Yamakawa, S. Mori, Y. Takenaga, N. Kobayashi, Y. Enokida, I. Yamamoto, Effect of cold wall temperature of thermal diffusion column on 14N15N-14N₂ isotope separation, J. Nucl. Sci. Technol. 37(2000) 710-715.
[35] H.-M. Yeh, Numerical model for separation of H-D gas mixture in batch-type concentric-tube thermal diffusion columns, Fusion Eng. Des. 84(2009) 43-48.
[36] A. Anazadehsayed, M. Barzegar Gerdroodbary, Y. Amini, R. Moradi, Mixing augmentation of transverse hydrogen jet by injection of micro air jets in supersonic crossflow, Acta Astronaut. 137(2017) 403-414.
[37] M. Barzegar Gerdroodbary, Y. Amini, D.D. Ganji, M.R. Takam, The flow feature of transverse hydrogen jet in presence of micro air jets in supersonic flow, Adv. Space Res. 59(2017) 1330-1340.
[38] R. Taylor, R. Krishna, Multicomponent Mass Transfer, John Wiley & Sons, 1993.
[39] M. Barzegar Gerdroodbary, D.D. Ganji, Y. Amini, Numerical study of shock wave interaction on transverse jets through multiport injector arrays in supersonic crossflow, Acta Astronaut. 115(2015) 422-433.
[40] R. Moradi, A. Mahyari, M. Barzegar Gerdroodbary, A. Abdollahi, Y. Amini, Shape effect of cavity flameholder on mixing zone of hydrogen jet at supersonic flow, Int. J. Hydrog. Energy 43(33) (2018) 16364-16372.
[41] R. Moradi, M. Mosavat, M. Barzegar Gerdroodbary, A. Abdollahi, Y. Amini, The influence of coolant jet direction on heat reduction on the nose cone with Aerodome at supersonic flow, Acta Astronaut. 151(2018) 487-493.
[42] M.K. Nikou, M. Ehsani, Turbulence models application on CFD simulation of hydrodynamics, heat and mass transfer in a structured packing, Int. Commun. Heat Mass Transfer 35(2008) 1211-1219.
[43] J. Wesselingh, R. Krishna, Mass Transfer in Multicomponent Mixtures, Delft University Press Delft, 2000.
[44] A. Leahy-Dios, M.M. Bou-Ali, J.K. Platten, A. Firoozabadi, Measurements of molecular and thermal diffusion coefficients in ternary mixtures, J. Chem. Phys. 122(2005) 234502.
[45] P. Polyakov, F. Müller-Plathe, S. Wiegand, Reverse nonequilibrium molecular dynamics calculation of the soret coefficient in liquid heptane/benzene mixtures, J. Phys. Chem. B 112(2008) 14999-15004.
[46] P. Costesèque, J.-C. Loubet, Measuring the Soret coefficient of binary hydrocarbon mixtures in packed thermogravitational columns (contribution of Toulouse University to the benchmark test), Philos. Mag. 83(2003) 2017-2022.
[47] I. Yamamoto, A. Kanagawa, Optimum cut of separating element as a function of total separation factor, J. Nucl. Sci. Technol. 27(1990) 584-586.
[48] J. Navarro, J. Madariaga, C. Santamarià, J. Savirón, J. Carrión, Thermal diffusion factor for carbon tetrachloride-cyclohexane and benzene-n-heptane mixtures from thermogravitational column separation, Sep. Sci. Technol. 20(1985) 335-343.
[49] H.G. Wood, C. Ying, S. Zeng, Y. Nie, X. Shang, Estimation of overall separation factor of a gas centrifuge for different multicomponent mixtures by separation theory for binary case, Sep. Sci. Technol. 37(2002) 417-430.
[50] H.-M. Yeh, H.C. Ward, The improvement in separation of concentric tube thermal diffusion columns, Chem. Eng. Sci. 26(1971) 937-947.
[51] N.B. Vargaftik, Handbook of physical properties of liquids and gases-pure substances and mixtures, Springer, Berlin, 1975.
[52] J. Demichowicz-Pigoniowa, M. Mitchell, H. Tyrrell, Thermal diffusion in the nheptane-benzene system at 25℃, J. Chem. Soc. A (1971) 307-309.
[53] M. Bou-Ali, O. Ecenarro, J. Madariaga, C. Santamaria, J. Valencia, Soret coefficient of some binary liquid mixtures, J. Non-Equilib. Thermodyn. 24(1999) 228-233.
[54] R. Piazza, A. Guarino, Soret effect in interacting micellar solutions, Phys. Rev. Lett. 88(2002) 208302.
[55] S. Wiegand, Thermal diffusion in liquid mixtures and polymer solutions, J. Phys. Condens. Matter 16(2004) R357.
[56] K. Zhang, M. Briggs, R. Gammon, J. Sengers, Optical measurement of the Soret coefficient and the diffusion coefficient of liquid mixtures, J. Chem. Phys. 104(1996) 6881-6892.
[57] N. Kobayashi, I. Yamamoto, Thermal diffusion coefficient in multi-component mixture expressed in terms of binary thermal diffusion factors and binary diffusion coefficients, J. Nucl. Sci. Technol. 32(1995) 1236-1242.
[58] A. Perronace, C. Leppla, F. Leroy, B. Rousseau, S. Wiegand, Soret and mass diffusion measurements and molecular dynamics simulations of n-pentane-ndecane mixtures, J. Chem. Phys. 116(2002) 3718-3729.
[59] K. Shukla, A. Firoozabadi, A new model of thermal diffusion coefficients in binary hydrocarbon mixtures, Ind. Eng. Chem. Res. 37(1998) 3331-3342.
[60] S. Chapman, T.G. Cowling, The Mathematical Theory of Non-uniform Gases:An Account of The Kinetic Theory of Viscosity, Thermal Conduction and Diffusion in Gases, Cambridge University Press, 1970.
[61] P. Polyakov, E. Rossinsky, S. Wiegand, Study of the Soret effect in hydrocarbon chain/aromatic compound mixtures, J. Phys. Chem. B 113(2009) 13308-13312.
[62] I. Yamamoto, A. Kanagawa, Optimum cut of separating element as function of total separation factor and mole fraction of component to be separated, J. Nucl. Sci. Technol. 28(1991) 858-862.
[63] H.-M. Yeh, Optimal plate aspect ratio for the enrichment of heavy water from water-isotope mixture in a flat-plate thermal diffusion column with transverse sampling streams, Nucl. Eng. Des. 239(2009) 1254-1259.