Numerical investigation of granular mixing in an intensive mixer: Effect of process and structural parameters on mixing performance and power consumption

doi:10.1016/j.cjche.2020.10.036

Abstract

Abstract: Discrete element method (DEM) simulations of particle mixing process in an intensive mixer were conducted to study the influence of structural and process parameters on the mixing performance and power consumption. The DEM model was verified by comparing the impeller torque obtained from simulation with that from experiment. Impeller and vessel torque, coordination number (CN) and mixing index (Relative standard deviation) were adopted to qualify the particle dynamics and mixing performance with different parameters. A method based on cubic polynomial fitting was proposed to determine the critical mixing time and critical specific input work during the mixing process. It is found that the mixing performance and energy efficiency increases with the decrease of impeller offset. The mixing performance is improved slightly with the increase of blade number and the impeller with 3 blades has the highest energy efficiency due to its low input torque. Results indicate that the energy efficiency and the mixing performance increase with the decrease of filling level when the height of granular bed is higher than that of blade.

Key words: Intensive mixer, Particle mixing, DEM, Mixing performance, Power consumption

摘要： Discrete element method (DEM) simulations of particle mixing process in an intensive mixer were conducted to study the influence of structural and process parameters on the mixing performance and power consumption. The DEM model was verified by comparing the impeller torque obtained from simulation with that from experiment. Impeller and vessel torque, coordination number (CN) and mixing index (Relative standard deviation) were adopted to qualify the particle dynamics and mixing performance with different parameters. A method based on cubic polynomial fitting was proposed to determine the critical mixing time and critical specific input work during the mixing process. It is found that the mixing performance and energy efficiency increases with the decrease of impeller offset. The mixing performance is improved slightly with the increase of blade number and the impeller with 3 blades has the highest energy efficiency due to its low input torque. Results indicate that the energy efficiency and the mixing performance increase with the decrease of filling level when the height of granular bed is higher than that of blade.

关键词: Intensive mixer, Particle mixing, DEM, Mixing performance, Power consumption

Zhijian Zuo, Shuguang Gong, Guilan Xie. Numerical investigation of granular mixing in an intensive mixer: Effect of process and structural parameters on mixing performance and power consumption[J]. Chinese Journal of Chemical Engineering, 2021, 32(4): 241-252.

References

[1] X.W. Xiao, Y.Q. Tan, H. Zhang, R. Deng, S.Q. Jiang, Experimental and DEM studies on the particle mixing performance in rotating drums:Effect of area ratio, Powder Technol. 314(2017) 182-194.
[2] X. Chen, J. Shen, Numerical analysis of mixing behaviors of two types of Eshape micromixer, Int. J. Heat Mass Transf. 106(MAR) (2017) 593-600.
[3] X. Chen, T. Li, A novel passive micromixer designed by applying an optimization algorithm to the zigzag microchannel, Chem. Eng. J. 313(2017) 1406-1414.
[4] H. Nadeem, T.J. Heindel, Review of noninvasive methods to characterize granular mixing, Powder Technol. 332(2018) 331-350.
[5] B. Remy, J.G. Khinast, B.J. Glasser, Polydisperse granular flows in a bladed mixer:experiments and simulation of cohesionless spheres, Chem. Eng. Sci. 60(2011) 1811-1824.
[6] S.L. Conway, A. Lekhal, J.G. Khinast, B.J. Glasser, Granular flow and segregation in a four-bladed mixer, Chem. Eng. Sci. 60(2005) 7091-7107.
[7] R.L. Stewart, J. Bridgwater, Y.C. Zhou, A.B. Yu, Simulated and measured flow of granules in a bladed mixer-a detailed comparison, Chem. Eng. Sci. 56(2001) 5457-5471.
[8] S.G. Gong, Z.J. Zuo, G.L. Xie, H.S. Lu, J.P. Zhang, Numerical simulation of wet particle flows in an intensive mixer, Powder Technol. 346(2019) 301-315.
[9] Z. Zuo, S. Gong, G. Xie, Numerical simulation of granular mixing in a rotary drum using a generalized interpolation material point method, Asia Pac. J. Chem. Eng. 15(2020).
[10] B. Alchikh-Sulaiman, M. Alian, F. Ein-Mozaffari, A. Lohi, S.R. Upreti, Using the discrete element method to assess the mixing of Polydisperse solid particles in a rotary drum, Particuology 25(2016) 133-142.
[11] N. Gui, X.T. Yang, J.Y. Tu, S.Y. Jiang, Z. Zhang, Numerical simulation of tetrahedral particle mixing and motion in rotating drums, Particuology 39(2018) 1-11.
[12] S. Radl, E. Kalvoda, B.J. Glasser, J.G. Khinast, Mixing characteristics of wet granular matter in a bladed mixer, Powder Technol. 200(2010) 171-189.
[13] J. Havlica, K. Jirounkova, T. Travnickova, M. Kohout, The effect of rotational speed on granular flow in a vertical bladed mixer, Powder Technol. 280(2015) 180-190.
[14] T.Q. Tang, Y.R. He, T. Tai, D.S. Wen, DEM numerical investigation of wet particle flow behaviors in multi-spout fluidized beds, Chem. Eng. Sci. 172(2017) 79-99.
[15] H. Zhang, S. Li, DEM simulation of wet granular-fluid flows in spouted beds:Numerical studies and experimental verifications, Powder Technol. 318(2017) 337-349.
[16] F. Göbel, S. Golshan, H.R. Norouzi, R. Zarghami, N. Mostoufi, Simulation of granular mixing in a static mixer by the discrete element method, Powder Technol. 346(2019) 171-179.
[17] H.P. Zhu, Z.Y. Zhou, R.Y. Yang, A.B. Yu, Discrete particle simulation of particulate systems:a review of major applications and findings, Chem. Eng. Sci. 63(2008) 5728-5770.
[18] Y.Y. Bao, T.C. Li, D.F. Wang, Z.Q. Cai, Z.M. Gao, Discrete element method study of effects of the impeller configuration and operating conditions on particle mixing in a cylindrical mixer, Particuology 49(2020) 146-158.
[19] V. Boonkanokwong, R.P. Frank, P. Valliappan, B. Remy, J.G. Khinast, B.J. Glasser, Flow of granular materials in a bladed mixer:Effect of particle properties and process parameters on impeller torque and power consumption, Adv. Powder Technol. 29(2018) 2733-2752.
[20] M.K. Saeed, M.S. Siraj, Mixing study of non-spherical particles using DEM, Powder Technol. 344(2019) 617-627.
[21] D. Höhner, S. Wirtz, V. Scherer, A study on the influence of particle shape and shape approximation on particle mechanics in a rotating drum using the discrete element method, Powder Technol. 253(2014) 256-265.
[22] A. Jarray, V. Magnanimo, S. Luding, Wet granular flow control through liquid induced cohesion, Powder Technol. 341(2019) 126-139.
[23] C.C. Liao, S.S. Hsiau, S.F. Wen, Effect of adding a small amount of liquid on density-induced wet granular segregation in a rotating drum, Adv. Powder Technol. 27(2016) 1265-1271.
[24] B. Remy, J.G. Khinast, B.J. Glasser, Wet granular flows in a bladed mixer:experiments and simulations of monodisperse spheres, AIChE J. 58(2012) 3354-3369.
[25] M. Umer, M.S. Siraj, DEM studies of Polydisperse wet granular flows, Powder Technol. 328(2018) 309-317.
[26] Y. Tsuji, T. Tanaka, T. Ishida, Lagrangian numerical simulation of plug flow of cohesionless particles in a horizontal pipe, Powder Technol. 71(1992) 239-250.
[27] B. Remy, J.G. Khinast, B.J. Glasser, Discrete element simulation of free flowing grains in a four-bladed mixer, AIChE J. 55(2009) 2035-2048.
[28] H. Chen, Y.G. Xiao, Y.L. Liu, Y.S. Shi, Effect of Young's modulus on DEM results regarding transverse mixing of particles with a rotating drum, Powder Technol. 318(2017) 507-517.
[29] G.R. Chandratilleke, A.B. Yu, J. Bridgewater, K. Shinohara, A particle-scale index in the quantification of mixing of particles, AIChE J. 58(2012) 1099-1118.
[30] L.E.M.D. Chazel, Y.C. Hung, A study of the effect of sample size on the analysis of power mixture, AIChE J. 14(1968) 169-173.
[31] M.M.H.D. Arntz, W.K. den Otter, W.J. Briels, P.J.T. Bussmann, H.H. Beeftink, R.M. Boom, Granular mixing and segregation in horizontal rotating drum:A simulation study on the impact of rotational speed and fill level, AIChE J. 54(12) (2008) 3133-3146.
[32] R.M. German, Metallurgy Science, Metal Powder Industries Federation, Princeton, NJ, 1984.
[33] Y.Y. Bao, Y. Lu, Z.Q. Cai, Z.M. Gao, Effects of rotational speed and fill level on particle mixing in a stirred tank with different impellers, Chin. J. Chem. Eng. 26(2018) 1383-1391.
[34] Z.X. Zhang, L. Wang, Y.R. Wang, X.H. Chu, Discrete element simulation on mixing of granular materials in rotated container, Eng. Anal. Boundary Elem. 106(2019) 20-26.
[35] M. Kwapinska, G. Saage, E. Tsotsas, Mixing of particles in rotary drums:a comparison of discrete element simulations with experimental results and penetration models for thermal processes, Powder Technol. 161(1) (2006) 69-78.
[36] V. Boonkanokwong, B. Remy, J.G. Khinast, B.J. Glasser, The effect of the number of impeller blades on granular flow in a bladed mixer, Powder Technol. 302(2016) 333-349.
[37] R.K. Soni, R. Mohanty, S. Mohanty, B.K. Mishra, Numerical analysis of mixing of particles in drum mixers using DEM, Adv. Powder Technol. 27(2016) 531-540.
[38] B. Remy, B.J. Glasser, J.G. Khinast, The effect of mixer properties and fill level on granular flow in a bladed mixer, AIChE J. 56(2) (2010) 336-353.