A numerical study of accelerated moderate or intense low-oxygen dilution (MILD) combustion stability for methane in a lab-scale furnace by off-stoichiometric combustion technology

doi:10.1016/j.cjche.2020.09.053

中国化学工程学报 ›› 2021, Vol. 32 ›› Issue (4): 108-118.DOI: 10.1016/j.cjche.2020.09.053

• Fluid Dynamics and Transport Phenomena • 上一篇下一篇

A numerical study of accelerated moderate or intense low-oxygen dilution (MILD) combustion stability for methane in a lab-scale furnace by off-stoichiometric combustion technology

Mengqian Xie^1,2, Fangqin Dai^1,2, Yaojie Tu³

1 The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, China;
2 Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081, China;
3 School of Energy and Power Engineering, Huazhong University of Science and Technology, Wuhan 430074, China

收稿日期:2020-05-22 修回日期:2020-08-25 出版日期:2021-04-28 发布日期:2021-06-19
通讯作者: Yaojie Tu
基金资助:
Yaojie Tu gratefully acknowledges the financial support from the National Natural Science Foundation of China (52006077) and Innovation Research Foundation of Huazhong University of Science and Technology (5001120031).

A numerical study of accelerated moderate or intense low-oxygen dilution (MILD) combustion stability for methane in a lab-scale furnace by off-stoichiometric combustion technology

Mengqian Xie^1,2, Fangqin Dai^1,2, Yaojie Tu³

1 The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, China;
2 Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081, China;
3 School of Energy and Power Engineering, Huazhong University of Science and Technology, Wuhan 430074, China

Received:2020-05-22 Revised:2020-08-25 Online:2021-04-28 Published:2021-06-19
Contact: Yaojie Tu
Supported by:
Yaojie Tu gratefully acknowledges the financial support from the National Natural Science Foundation of China (52006077) and Innovation Research Foundation of Huazhong University of Science and Technology (5001120031).

摘要/Abstract

摘要： Moderate or intense low-oxygen dilution (MILD) combustion has become a promising low-NO_X emission technology, while the delayed mixing of reactants and slower oxidation rate could potentially cause ignition instability in some scenarios. This paper proposes a new idea for enhancing the ignition stability for methane MILD combustion by combining with off-stoichiometric combustion (OSC), and its performances have been numerically assessed through a comparison against the original MILD combustion burner. The results reveal although non-premixed pattern has the lowest NO emission, it suffers from a larger liftoff distance, thus less ignition stability. Contrarily, both partially-premixed and fully premixed patterns exhibit excellent ignition stability. Among the considered OSC conditions, the pattern of Inner ultra-rich and Outer lean produces the lowest NO emission while maintains a high ignition stability. Furthermore, the enhancement of the combustion stability by implementing OSC to the original MILD combustion burner is shown by comparing the operational range of furnace wall temperature (T_f), CO and NO emissions, as well as the evolution of chemical flame. The comparison reveals that OSC can extend the lowest operational T_f from 900 K to 800 K. More importantly, OSC can significantly improve the ignition stability in the whole range of T_f as compared to the original MILD combustion burner.

关键词: MILD combustion, Off-stoichiometric combustion, NO emission, Ignition instability, Burner design

Abstract: Moderate or intense low-oxygen dilution (MILD) combustion has become a promising low-NO_X emission technology, while the delayed mixing of reactants and slower oxidation rate could potentially cause ignition instability in some scenarios. This paper proposes a new idea for enhancing the ignition stability for methane MILD combustion by combining with off-stoichiometric combustion (OSC), and its performances have been numerically assessed through a comparison against the original MILD combustion burner. The results reveal although non-premixed pattern has the lowest NO emission, it suffers from a larger liftoff distance, thus less ignition stability. Contrarily, both partially-premixed and fully premixed patterns exhibit excellent ignition stability. Among the considered OSC conditions, the pattern of Inner ultra-rich and Outer lean produces the lowest NO emission while maintains a high ignition stability. Furthermore, the enhancement of the combustion stability by implementing OSC to the original MILD combustion burner is shown by comparing the operational range of furnace wall temperature (T_f), CO and NO emissions, as well as the evolution of chemical flame. The comparison reveals that OSC can extend the lowest operational T_f from 900 K to 800 K. More importantly, OSC can significantly improve the ignition stability in the whole range of T_f as compared to the original MILD combustion burner.

Key words: MILD combustion, Off-stoichiometric combustion, NO emission, Ignition instability, Burner design

Mengqian Xie, Fangqin Dai, Yaojie Tu. A numerical study of accelerated moderate or intense low-oxygen dilution (MILD) combustion stability for methane in a lab-scale furnace by off-stoichiometric combustion technology[J]. 中国化学工程学报, 2021, 32(4): 108-118.

参考文献

[1] A. Cavaliere, M. de Joannon, Mild combustion, Prog. Energy Combust. Sci. 30(2004) 329-366.
[2] J. Wünning, J. Wünning, Flameless oxidation to reduce thermal NO-formation, Prog. Energy Combust. Sci. 23(1997) 81-94.
[3] R. Weber, S. Orsino, N. Lallemant, A. Verlaan, Combustion of natural gas with high-temperature air and large quantities of flue gas, Proc. Combust. Inst. 28(2000) 1315-1321.
[4] Y. Tu, K. Su, H. Liu, Z. Wang, Y. Xie, C. Zheng, W. Li, MILD combustion of natural gas using low preheating temperature air in an industrial furnace, Fuel Process. Technol. 156(2017) 72-81.
[5] P. Li, F. Wang, Y. Tu, Z. Mei, J. Zhang, Y. Zheng, H. Liu, Z. Liu, J. Mi, C. Zheng, Moderate or intense low-oxygen dilution oxy-combustion characteristics of light oil and pulverized coal in a pilot-scale furnace, Energy Fuels. 28(2014) 1524-1535.
[6] G. Szegö, B. Dally, G. Nathan, Scaling of NO_X emissions from a laboratory-scale mild combustion furnace, Combust Flame 154(2008) 281-295.
[7] M. Tamura, S. Watanabe, K. Komaba, K. Okazaki, Combustion behaviour of pulverised coal in high temperature air condition for utility boilers, Appl. Therm. Eng. 75(2015) 445-450.
[8] N. Schaffel, M. Mancini, A. Szle, R. Weber, Mathematical modeling of MILD combustion of pulverized coal, Combust. Flame 156(2009) 1771-1784.
[9] A. Peters, R. Weber, Mathematical modeling of a 2. 25 MWt swirling natural Gas flame. Part 1:Eddy break-up concept for turbulent combustion; probability density function approach for nitric oxide formation, Combust. Sci. Technol. 110(1995) 67-101.
[10] A.A. Peters, R. Weber, Mathematical modeling of a 2.4 MW swirling pulverized coal flame, Combust. Sci. Technol. 122(1997) 131-182.
[11] M. Saha, B.B. Dally, P.R. Medwell, E.M. Cleary, Moderate or intense low oxygen dilution (MILD) combustion characteristics of pulverized coal in a selfrecuperative furnace, Energy Fuels 28(2014) 6046-6057.
[12] C.K. Law, A. Makino, T. Lu, On the off-stoichiometric peaking of adiabatic flame temperature, Combust. Flame 145(2006) 808-819.
[13] N. Rizk, H. Mongia, Low NO_X rich-lean combustion concept application, 27th Joint Propulsion Conference, Sacramento, CA, USA, 1991.
[14] L. Zhengqi, Y. LongBin, Q. Penghua, S. Rui, C. LiZhe, S. ShaoZeng, Experimental study of the combustion efficiency and formation of NO_X in an industrial pulverized coal combustor, Int. J. Energy Res. 28(2004) 511-520.
[15] D. Bradley, P. Gaskell, X. Gu, M. Lawes, M. Scott, Premixed turbulent flame instability and NO formation in a lean-burn swirl burner, Combust. Flame. 115(1998) 515-538.
[16] X. Zhang, J. Zhou, S. Sun, R. Sun, M. Qin, Numerical investigation of low NO_X combustion strategies in tangentially-fired coal boilers, Fuel 142(2015) 215-221.
[17] Q. Zha, D. Li, D. Che, Numerical evaluation of heat transfer and NO_X emissions under deep-air-staging conditions within a 600 MWe tangentially fired pulverized-coal boiler, Appl. Therm. Eng. 116(2017) 170-181.
[18] O. Kurata, N. Iki, T. Inoue, T. Matsunuma, T. Tsujimura, H. Furutani, M. Kawano, K. Arai, E.C. Okafor, A. Hayakawa, Development of a wide range-operable, richlean low-NO_X combustor for NH3 fuel gas-turbine power generation, Proc. Combust. Inst. 37(2019) 4587-4595.
[19] F. Bolaños, D. Winkler, F. Piringer, T. Griffin, R. Bombach, J. Mantzaras, Study of a rich/lean staged combustion concept for hydrogen at gas turbine relevant conditions, ASME Turbo Expo 2013:Turbine Technical Conference and Exposition:American Society of Mechanical Engineers Digital Collection, San Antonio, Texas, USA, 2013.
[20] M. Xu, Y. Tu, G. Zeng, Q. Wang, A. Zhou, W. Yang, Numerical study of further NO_X emission reduction for coal MILD combustion by combining fuel-rich/lean technology, Int. J. Energy Res. 43(2019) 8492-8508.
[21] P. Li, J. Mi, B.B. Dally, R.A. Craig, F. Wang, Premixed moderate or intense lowoxygen dilution (MILD) combustion from a single jet burner in a laboratoryscale furnace, Energy Fuels 25(2011) 2782-2793.
[22] P. Li, F. Wang, J. Mi, B. Dally, Z. Mei, MILD combustion under different premixing patterns and characteristics of the reaction regime, Energy Fuels 28(2014) 2211-2226.
[23] S. Cao, C. Zou, Q. Han, Y. Liu, D. Wu, C. Zheng, Numerical and experimental studies of NO formation mechanisms under methane moderate or intense low-oxygen dilution (MILD) combustion without heated air, Energy Fuels 29(2015) 1987-1996.
[24] ANSYS Fluent 18.2 User's Manual. ANSYS Canonsburg, PA, 2017.
[25] F.C. Christo, B.B. Dally, Modeling turbulent reacting jets issuing into a hot and diluted coflow, Combust. Flame 142(2005) 117-129.
[26] A. De, E. Oldenhof, P. Sathiah, D. Roekaerts, Numerical simulation of delft-jetin-hot-coflow (djhc) flames using the eddy dissipation concept model for turbulence-chemistry interaction, Flow, Turbul. Combust. 87(2011) 537-567.
[27] M. Evans, P. Medwell, Z.J.C.S. Tian, Modeling lifted jet flames in a heated coflow using an optimized eddy dissipation concept model, Combust. Sci. Technol. 187(2015) 1093-1109.
[28] Y. Tu, W. Yang, H. Liu, A refined global reaction mechanism for gently preheated MILD combustion of methane, Energy Fuels 31(2017) 10144-10157.
[29] J.P. Kim, U. Schnell, G. Scheffknecht, Comparison of different global reaction mechanisms for mild combustion of natural gas, Combust. Sci. Technol. 180(2008) 565-592.
[30] L. Wang, Z. Liu, S. Chen, C. Zheng, Comparison of different global combustion mechanisms under hot and diluted oxidation conditions, Combust. Sci. Technol. 184(2012) 259-276.
[31] G.P. Smith, D.M. Golden, M. Frenklach, N.W. Moriarty, B. Eiteneer, M. Goldenberg, et al. GRI-Mech 3.0, 1999, http://www.me.berkeley.edu/gri_mech.
[32] B. Jiang, H. Liang, G. Huang, L. Xingang, Study on NO_X formation in CH₄/Air jet combustion, Chin. J. Chem. Eng. 14(2006) 723-728.
[33] Y. Liu, J. Cheng, C. Zou, L. Cai, Y. He, C. Zheng, Experimental and numerical study on the CO formation mechanism in methane MILD combustion without preheated air, Fuel 192(2017) 140-148.
[34] Y. Tu, M. Xu, D. Zhou, Q. Wang, W. Yang, H. Liu, CFD and kinetic modelling study of methane MILD combustion in O₂/N₂, O₂/CO₂ and O₂/H₂O atmospheres, Appl. Energy 240(2019) 1003-1013.
[35] M. Jianchun, L. Pengfei, C. Zheng, Numerical simulation of flameless premixed combustion with an annular nozzle in a recuperative furnace, Chin. J. Chem. Eng. 18(2010) 10-17.
[36] W. Hawthorne, D. Weddell, H. Hottel, Mixing and combustion in turbulent gas jets, in:Symposium on Combustion and Flame, and Explosion Phenomena, Elsevier, Amsterdam (1948) 266-288.
[37] S.R. Turns, F.H. Myhr, R.V. Bandaru, E.R. Maund, Oxides of nitrogen emissions from turbulent jet flames:part II-fuel dilution and partial premixing effects, Combust. Flame 93(1993) 255-269.
[38] Z. Mei, J. Mi, F. Wang, P. Li, J. Zhang, Chemical flame length of a methane jet into oxidant stream, Flow, Turbul. Combust. 94(2015) 767-794.
[39] J.S. Newman, C. Wieczorek, Chemical flame heights, Fire Saf. J. 39(2004) 375-382.
[40] W. Yang, W. Blasiak, Chemical flame length and volume in liquified propane gas combustion using high-temperature and low-oxygen-concentration oxidizer, Energy Fuels 18(2004) 1329-1335.
[41] R. Stephen, An Introduction to Combustion:Concepts and Applications, McGraw-hill, New York, USA, 2000.
[42] K.A. Khazaei, A.A. Hamidi, M. Rahimi, Numerical investigation of fuel dilution effects on the performance of the conventional and the highly preheated and diluted air combustion furnaces, Chin. J. Chem. Eng. 17(2009) 711-726.
[43] S. Xu, Y. Tu, P. Huang, C. Luan, Z. Wang, B. Shi, H. Liu, Z. Liu, Effects of wall temperature on methane MILD combustion and heat transfer behaviors with non-preheated air, Appl. Therm. Eng. 174(2020) 115282.
[44] C. Luan, S. Xu, B. Shi, Y. Tu, H. Liu, P. Li, Z. Liu, Re-recognition of MILD combustion regime by initial conditions of T_in and X_O2 for methane in a nonadiabatic well-stirred reactor, Energy Fuels 34(2020) 2391-2404.

A numerical study of accelerated moderate or intense low-oxygen dilution (MILD) combustion stability for methane in a lab-scale furnace by off-stoichiometric combustion technology

A numerical study of accelerated moderate or intense low-oxygen dilution (MILD) combustion stability for methane in a lab-scale furnace by off-stoichiometric combustion technology

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价