Comparison of the effect of carbon, halloysite and titania nanotubes on the mechanical and thermal properties of LDPE based nanocomposite films

doi:10.1016/j.cjche.2017.09.017

Abstract

Abstract: In this study, titania nanotubes (TNTs) were prepared by hydrothermal method with the aim to compare the properties of these one-dimensional tubular nanostructures' reinforced nanocomposites with the carbon and halloysite nanotubes' (CNTs and HNTs, respectively) reinforced nanocomposites. Low density polyethylene (LDPE) was used as the matrix material. The prepared nanocomposites were characterized and compared by means of their morphological, mechanical and thermal properties. SEM results showed enhanced interfacial interaction and better dispersion of TNTs and HNTs into LDPE with the incorporation of a MAPE compatibilizer, however, these interactions seem to be absent between CNTs and LDPE, and the CNTs remained agglomerated. Contact angle measurements revealed that CNT filled nanocomposites are more hydrophilic than HNT composites, and less than TNT composites. CNTs provided better tensile strength and Young's modulus than HNT and TNT nanocomposites, a 42% increase in tensile strength and Young's modulus is achieved compared to LDPE. Tear strength improvement was noticed in the TNT composites with a value of 35.4 N·mm^-1, compared to CNT composites with a value of 25.5 N·mm^-1·s^-1. All the prepared nanocomposites are more thermally stable than neat LDPE and the best improvement in thermal stability was observed for CNT reinforced nanocomposites. CNTs depicted the best improvement in tensile and thermal properties and the MAPE compatibilizer effectiveness regarding morphological, mechanical and thermal properties was only observed for TNT and HNT systems.

Key words: Hydrothermal, Nanostructure, Nanotube, Nanocomposite, Mechanical properties, Thermal properties

摘要： In this study, titania nanotubes (TNTs) were prepared by hydrothermal method with the aim to compare the properties of these one-dimensional tubular nanostructures' reinforced nanocomposites with the carbon and halloysite nanotubes' (CNTs and HNTs, respectively) reinforced nanocomposites. Low density polyethylene (LDPE) was used as the matrix material. The prepared nanocomposites were characterized and compared by means of their morphological, mechanical and thermal properties. SEM results showed enhanced interfacial interaction and better dispersion of TNTs and HNTs into LDPE with the incorporation of a MAPE compatibilizer, however, these interactions seem to be absent between CNTs and LDPE, and the CNTs remained agglomerated. Contact angle measurements revealed that CNT filled nanocomposites are more hydrophilic than HNT composites, and less than TNT composites. CNTs provided better tensile strength and Young's modulus than HNT and TNT nanocomposites, a 42% increase in tensile strength and Young's modulus is achieved compared to LDPE. Tear strength improvement was noticed in the TNT composites with a value of 35.4 N·mm^-1, compared to CNT composites with a value of 25.5 N·mm^-1·s^-1. All the prepared nanocomposites are more thermally stable than neat LDPE and the best improvement in thermal stability was observed for CNT reinforced nanocomposites. CNTs depicted the best improvement in tensile and thermal properties and the MAPE compatibilizer effectiveness regarding morphological, mechanical and thermal properties was only observed for TNT and HNT systems.

关键词: Hydrothermal, Nanostructure, Nanotube, Nanocomposite, Mechanical properties, Thermal properties

Khaliq Majeed, Mariam Al Ali AlMaadeed, Moustafa M. Zagho. Comparison of the effect of carbon, halloysite and titania nanotubes on the mechanical and thermal properties of LDPE based nanocomposite films[J]. Chin.J.Chem.Eng., 2018, 26(2): 428-435.

References

[1] R.H. Baughman, A.A. Zakhidov, W.A. de Heer, Carbon nanotubes-the route toward applications, Science 297(2002) 787-792.

[2] C.N.R. Rao, M. Nath, Inorganic nanotubes, Dalton Trans. (2003) 1-24.

[3] M. Micusik, M. Omastova, I. Krupa, J. Prokes, P. Pissis, E. Logakis, C. Pandis, P. Pötschke, J. Pionteck, A comparative study on the electrical and mechanical behaviour of multi-walled carbon nanotube composites prepared by diluting a masterbatch with various types of polypropylenes, J. Appl. Polym. Sci. 113(2009) 2536-2551.

[4] K. Prashantha, J. Soulestin, M. Lacrampe, M. Claes, G. Dupin, P. Krawczak, Multi-walled carbon nanotube filled polypropylene nanocomposites based on masterbatch route:improvement of dispersion and mechanical properties through PP-g-MA addition, Express Polym. Lett. 2(2008) 735-745.

[5] X. Sun, Y. Li, Synthesis and characterization of ion-exchangeable titanate nanotubes, Chem. Eur. J. 9(2003) 2229-2238.

[6] C. Strobel, A.A. Torrano, R. Herrmann, M. Malissek, C. Brauchle, A. Reller, L. Treuel, I. Hilger, Effects of the physicochemical properties of titanium dioxide nanoparticles, commonly used as sun protection agents, on microvascular endothelial cells, J. Nanopart. Res. 16(2014) 1-16.

[7] K. Lee, A. Mazare, P. Schmuki, One-dimensional titanium dioxide nanomaterials:nanotubes, Chem. Rev. 114(2014) 9385-9454.

[8] P. Roy, S. Berger, P. Schmuki, TiO₂ nanotubes:synthesis and applications, Angew. Chem. Int. Ed. 50(2011) 2904-2939.

[9] A. Okada, A. Usuki, Twenty years of polymer-clay nanocomposites, Macromol. Mater. Eng. 291(2006) 1449-1476.

[10] T.V. Duncan, Applications of nanotechnology in food packaging and food safety:barrier materials, antimicrobials and sensors, J. Colloid Interface Sci. 363(2011) 1-24.

[11] M. Alexandre, P. Dubois, Polymer-layered silicate nanocomposites:preparation, properties and uses of a new class of materials, Mater. Sci. Eng. R. Rep. 28(2000) 1-63.

[12] X. Wang, Z. Li, J. Shi, Y. Yu, One-dimensional titanium dioxide nanomaterials:nanowires, nanorods, and nanobelts, Chem. Rev. 114(2014) 9346-9384.

[13] P. Datta, C. Guha, G. Sarkhel, Mechanical, rheological, and electrical properties of multiwalled carbon nanotube reinforced ASA/Na-ionomer blend, J. Appl. Polym. Sci. 132(2015).

[14] N. Liu, X. Chen, J. Zhang, J.W. Schwank, A review on TiO₂-based nanotubes synthesized via hydrothermal method:formation mechanism, structure modification, and photocatalytic applications, Catal. Today 225(2014) 34-51.

[15] K. Marsh, B. Bugusu, Food packaging-roles, materials, and environmental issues, J. Food Sci. 72(2007) R39-R55.

[16] R. Chinkamonthong, A. Kositchaiyong, N. Sombatsompop, Effects of thermal and UV aging on antibacterial properties of linear low-density polyethylene and poly (vinyl chloride) films containing nano-silver colloid, J. Plast. Film Sheeting 29(2013) 144-162.

[17] T. McNally, P. Pötschke, P. Halley, M. Murphy, D. Martin, S.E. Bell, G.P. Brennan, D. Bein, P. Lemoine, J.P. Quinn, Polyethylene multiwalled carbon nanotube composites, Polymer 46(2005) 8222-8232.

[18] J. Vega, J. Martinez-Salazar, M. Trujillo, M. Arnal, A. Muller, S. Bredeau, P. Dubois, Rheology, processing, tensile properties, and crystallization of polyethylene/carbon nanotube nanocomposites, Macromolecules 42(2009) 4719-4727.

[19] V.P. Singh, K.K. Vimal, G.S. Kapur, S. Sharma, V. Choudhary, High-density polyethylene/halloysite nanocomposites:morphology and rheological behaviour under extensional and shear flow, J. Polym. Res. 23(2016) 1-17.

[20] Y.-J. Lin, L. Wang, W.-Y. Chiu, Preparation and characterization of titania nanotubes and hybrid materials derived from them, J. Vac. Sci. Technol. B 23(2005) 2398.

[21] P.P. Vijayan, M. Thomas, K. George, Effect of calcinations on electrical properties of TiO₂ nanotubes, J. Appl. Phys. 112(2012) 104308.

[22] C. Serrano, J.A. Ressia, E.M. Valles, M. Fernandez-Garcia, M.L. Cerrada, Interfacial agent effect on rheological response and crystallite characteristics in germicidal polypropylene/titanium dioxide nanocomposites, Polym. Int. 61(2012) 1655-1665.

[23] A.M. Mohamed, A.S. Aljaber, S.Y. AlQaradawi, N.K. Allam, TiO₂ nanotubes with ultrathin walls for enhanced water splitting, Chem. Commun. 51(2015) 12617-12620.

[24] A.J. Nathanael, D. Mangalaraj, P.C. Chen, N. Ponpandian, Mechanical and photocatalytic properties of hydroxyapatite/titania nanocomposites prepared by combined high gravity and hydrothermal process, Compos. Sci. Technol. 70(2010) 419-426.

[25] H. Yin, G. Ding, B. Gao, F. Huang, X. Xie, M. Jiang, Synthesis of ultrafine titanium dioxide nanowires using hydrothermal method, Mater. Res. Bull. 47(2012) 3124-3128.

[26] B. Mayoral, E. Harkin-Jones, P.N. Khanam, M. AlMaadeed, M. Ouederni, A. Hamilton, D. Sun, Melt processing and characterisation of polyamide 6/graphene nanoplatelet composites, RSC Adv. 5(2015) 52395-52409.

[27] Z. Jia, Y. Luo, B. Guo, B. Yang, M. Du, D. Jia, Reinforcing and flame-retardant effects of halloysite nanotubes on LLDPE, Polym.-Plast. Technol. Eng. 48(2009) 607-613.

[28] H.C. Bidsorkhi, H. Adelnia, R.H. Pour, M. Soheilmoghaddam, Preparation and characterization of ethylene-vinyl acetate/halloysite nanotube nanocomposites, J. Mater. Sci. 50(2015) 3237-3245.

[29] C. Espejo, A. Arribas, F. Monzo, P.P. Diez, Nanocomposite films with enhanced radiometric properties for greenhouse covering applications, J. Plast. Film Sheeting 28(2012) 336-350.

[30] N.A. Jamaludin, I.M. Inuwa, A. Hassan, N. Othman, M. Jawaid, Mechanical and thermal properties of SEBS-g-MA compatibilized halloysite nanotubes reinforced polyethylene terephthalate/polycarbonate/nanocomposites, J. Appl. Polym. Sci. 132(2015).

[31] V.G. Nguyen, H. Thai, D.H. Mai, H.T. Tran, M.T. Vu, Effect of titanium dioxide on the properties of polyethylene/TiO₂ nanocomposites, Compos. Part B Eng. 45(2013) 1192-1198.

[32] P.N. Khanam, M. AlMaadeed, Improvement of ternary recycled polymer blend reinforced with date palm fibre, Mater. Des. 60(2014) 532-539.

[33] W. Wu, X. Cao, Y. Zhang, G. He, Polylactide/halloysite nanotube nanocomposites:thermal, mechanical properties, and foam processing, J. Appl. Polym. Sci. 130(2013) 443-452.

[34] K. Majeed, A. Hassan, A.A. Bakar, Influence of maleic anhydride-grafted polyethylene compatibiliser on the tensile, oxygen barrier and thermal properties of rice husk and nanoclay-filled low-density polyethylene composite films, J. Plast. Film Sheeting 30(2014) 120-140.