Determination of interfacial tension and viscosity under dripping flow in a step T-junction microdevice

doi:10.1016/j.cjche.2021.07.028

Abstract

Abstract: Microfluidic approaches for the determination of interfacial tension and viscosity of liquid-liquid systems still face some challenges. One of them is liquid-liquid systems with low interfacial and high viscosity, because dripping flow in normal microdevices can't be easily realized for the systems. In this work, we designed a capillary embedded step T-junction microdevice to develop a modified microfluidic approach to determine the interfacial tension of several systems, specially, for the systems with low interfacial tension and high viscosity. This method combines a classical T-junction geometry with a step to strengthen the shear force further to form monodispersed water/oil (w/o) or aqueous two-phase (ATP) droplet under dripping flow. For systems with low interfacial tension and high viscosity, the operating range for dripping flow is relative narrow whereas a wider dripping flow operating range can be realized in this step T-junction microdevice when the capillary number of the continuous phase is in the range of 0.01 to 0.7. Additionally, the viscosity of the continuous phase was also measured in the same microdevice. Several different systems with an interfacial tension from 1.0 to 8.0 mN·m^-1 and a viscosity from 0.9 to 10 mPa·s were measured accurately. The experimental results are in good agreement with the data obtained from a commercial interfacial tensiometer and a spinning digital viscometer. This work could extend the application of microfluidic flows.

Key words: Step T-junction, Interfacial tension, Viscosity, Force balance

摘要： Microfluidic approaches for the determination of interfacial tension and viscosity of liquid-liquid systems still face some challenges. One of them is liquid-liquid systems with low interfacial and high viscosity, because dripping flow in normal microdevices can't be easily realized for the systems. In this work, we designed a capillary embedded step T-junction microdevice to develop a modified microfluidic approach to determine the interfacial tension of several systems, specially, for the systems with low interfacial tension and high viscosity. This method combines a classical T-junction geometry with a step to strengthen the shear force further to form monodispersed water/oil (w/o) or aqueous two-phase (ATP) droplet under dripping flow. For systems with low interfacial tension and high viscosity, the operating range for dripping flow is relative narrow whereas a wider dripping flow operating range can be realized in this step T-junction microdevice when the capillary number of the continuous phase is in the range of 0.01 to 0.7. Additionally, the viscosity of the continuous phase was also measured in the same microdevice. Several different systems with an interfacial tension from 1.0 to 8.0 mN·m^-1 and a viscosity from 0.9 to 10 mPa·s were measured accurately. The experimental results are in good agreement with the data obtained from a commercial interfacial tensiometer and a spinning digital viscometer. This work could extend the application of microfluidic flows.

关键词: Step T-junction, Interfacial tension, Viscosity, Force balance

Li Ma, Yongjin Cui, Lin Sheng, Chencan Du, Jian Deng, Guangsheng Luo. Determination of interfacial tension and viscosity under dripping flow in a step T-junction microdevice[J]. Chinese Journal of Chemical Engineering, 2022, 42(2): 210-218.

References

[1] W.X. Guo, C.Y. Zhu, T.T. Fu, Y.G. Ma, Coalescence dynamics of two droplets of different viscosities in T-junction microchannel with a funnel-typed expansion chamber, Chin. J. Chem. Eng. (2021) (in press)
[2] C.Q. Yao, H.Y. Ma, Q.K. Zhao, Y.Y. Liu, Y.C. Zhao, G.W. Chen, Mass transfer in liquid-liquid Taylor flow in a microchannel:Local concentration distribution, mass transfer regime and the effect of fluid viscosity, Chem. Eng. Sci. 223 (2020) 115734
[3] S.H. Shen, Y.G. Ma, S.M. Lu, C.Y. Zhu, An unsteady heterogeneous mass transfer model for gas absorption enhanced by dispersed third phase droplets, Chin. J. Chem. Eng. 17 (4) (2009) 602-607
[4] P. Xie, K. Wang, J. Deng, G.S. Luo, Continuous, homogeneous and rapid synthesis of 4-bromo-3-methylanisole in a modular microreaction system, Chin. J. Chem. Eng. 28 (8) (2020) 2092-2098
[5] Z.F. Yan, J.X. Tian, K. Wang, K.D.P. Nigam, G.S. Luo, Microreaction processes for synthesis and utilization of epoxides:a review, Chem. Eng. Sci. 229 (2021) 116071
[6] K. Wang, L.M. Zhang, W.L. Zhang, G.S. Luo, Mass-transfer-controlled dynamic interfacial tension in microfluidic emulsification processes, Langmuir 32 (13) (2016) 3174-3185
[7] A.M. Nightingale, T.W. Phillips, J.H. Bannock, J.C. de Mello, Controlled multistep synthesis in a three-phase droplet reactor, Nat Commun 5 (2014) 3777
[8] X.H. Ge, H. Zhao, T. Wang, J. Chen, J.H. Xu, G.S. Luo, Microfluidic technology for multiphase emulsions morphology adjustment and functional materials preparation, Chin. J. Chem. Eng. 24 (6) (2016) 677-692
[9] S. Goyal, M.R. Thorson, G.G.Z. Zhang, Y.C. Gong, P.J.A. Kenis, Microfluidic approach to cocrystal screening of pharmaceutical parent compounds, Cryst. Growth Des. 12 (12) (2012) 6023-6034
[10] G. Pascali, P. Watts, P.A. Salvadori, Microfluidics in radiopharmaceutical chemistry, Nucl Med Biol 40 (6) (2013) 776-787
[11] G.M. Whitesides, The origins and the future of microfluidics, Nature 442 (7101) (2006) 368-373
[12] T.C. Chang, A.M. Mikheev, W. Huynh, R.J. Monnat, R.C. Rostomily, A. Folch, Parallel microfluidic chemosensitivity testing on individual slice cultures, Lab Chip 14 (23) (2014) 4540-4551
[13] J.H. Xu, S.W. Li, W.J. Lan, G.S. Luo, Microfluidic approach for rapid interfacial tension measurement, Langmuir 24 (19) (2008) 11287-11292
[14] B. Zheng, L.S. Roach, R.F. Ismagilov, Screening of protein crystallization conditions on a microfluidic chip using nanoliter-size droplets, J Am Chem Soc 125 (37) (2003) 11170-11171
[15] D. Changpeng, C. White, Interfacial tension measurement in fluid-fluid systems, Encyclopedia of Surface and Colloid Science:Second Fdition (2006) 2966-2980. Retrieved from http://www.informaworld.com/10.1081/E-ESCS-120000636.
[16] Y.J. Cui, Y.K. Li, K. Wang, J. Deng, G.S. Luo, Determination of dynamic interfacial tension during the generation of tiny droplets in the liquid-liquid jetting flow regime, Langmuir 36 (45) (2020) 13633-13641
[17] J.K. Nunes, S.S. Tsai, J. Wan, H.A. Stone, Dripping and jetting in microfluidic multiphase flows applied to particle and fiber synthesis, J Phys D Appl Phys 46 (11) (2013) 114002
[18] P. Garstecki, H.A. Stone, G.M. Whitesides, Mechanism for flow-rate controlled breakup in confined geometries:a route to monodisperse emulsions, Phys Rev Lett 94 (16) (2005) 164501
[19] P. Garstecki, M.J. Fuerstman, H.A. Stone, G.M. Whitesides, Formation of droplets and bubbles in a microfluidic T-junction-scaling and mechanism of break-up, Lab Chip 6 (3) (2006) 437-446
[20] J.H. Xu, S.W. Li, J. Tan, Y.J. Wang, G.S. Luo, Preparation of highly monodisperse droplet in a T-junction microfluidic device, AIChE J. 52 (9) (2006) 3005-3010
[21] J. Tan, J.H. Xu, S.W. Li, G.S. Luo, Drop dispenser in a cross-junction microfluidic device:Scaling and mechanism of break-up, Chem. Eng. J. 136 (2-3) (2008) 306-311
[22] S.L. Anna, N. Bontoux, H.A. Stone, Formation of dispersions using "flow focusing" in microchannels, Appl. Phys. Lett. 82 (3) (2003) 364-366
[23] A.G. Marín, F. Campo-Cortés, J.M. Gordillo, Generation of micron-sized drops and bubbles through viscous coflows, Colloids Surfaces A:Physicochem. Eng. Aspects 344 (1-3) (2009) 2-7
[24] Link DR, Anna SL, Weitz DA, Stone HA, Geometrically mediated breakup of drops in microfluidic devices, Phys Rev Lett 92 (5) (2004) 054503
[25] T. Glawdel, C.L. Ren, Droplet formation in microfluidic T-junction generators operating in the transitional regime. III. Dynamic surfactant effects, Phys Rev E Stat Nonlin Soft Matter Phys 86 (2 Pt 2) (2012) 026308
[26] Q. Brosseau, J. Vrignon, J.C. Baret, Microfluidic dynamic interfacial tensiometry (μDIT), Soft Matter 10 (17) (2014) 3066-3076
[27] Y.G. Ma, X.Y. Ji, D.J. Wang, T.T. Fu, C.Y. Zhu, Measurement and correlation of pressure drop for gas-liquid two-phase flow in rectangular microchannels, Chin. J. Chem. Eng. 18 (6) (2010) 940-947
[28] L. Sheng, Y.C. Chen, K. Wang, J. Deng, G.S. Luo, General rules of bubble formation in viscous liquids in a modified step T-junction microdevice, Chem. Eng. Sci. 239 (2021) 116621
[29] S. D. Hudson, J. T. Cabral, W. J. Goodrum, K. L. Beers, E. J. Amis, Microfluidic interfacial tensiometry,Appl. Phys.Lett.87(8)(2005) 081905
[30] N.-T. Nguyen, S. Lassemono, F. A.C. Yang. Chollet, Microfluidic sensor for dynamic surface tension measurement, IEE Proc. Nanobiotechnol. 153 (4) (2006) 102-106
[31] N.T. Nguyen, S. Lassemono, F.A. Chollet, C. Yang, Microfluidic sensor for dynamic surface tension measurement, IEE Proc Nanobiotechnol 153 (4) (2006) 102-106
[32] X.Y. Wang, A. Riaud, K. Wang, G.S. Luo, Pressure drop-based determination of dynamic interfacial tension of droplet generation process in T-junction microchannel, Microfluid. Nanofluidics 18 (3) (2015) 503-512
[33] K. Wang, Y.C. Lu, J.H. Xu, G.S. Luo, Determination of dynamic interfacial tension and its effect on droplet formation in the T-shaped microdispersion process, Langmuir 25 (4) (2009) 2153-2158
[34] S.W. Li, J.H. Xu, Y.J. Wang, G.S. Luo, A new interfacial tension measurement method through a pore array micro-structured device, J. Colloid Interface Sci. 331 (1) (2009) 127-131
[35] W.J. Lan, C. Wang, X.Q. Guo, S.W. Li, G.S. Luo, Study on the transient interfacial tension in a microfluidic droplet formation coupling interphase mass transfer process, AIChE J. 62 (7) (2016) 2542-2549
[36] Y.C. Chao, H.C. Shum, Emerging aqueous two-phase systems:from fundamentals of interfaces to biomedical applications, Chem. Soc. Rev. 49 (1) (2020) 114-142
[37] Y.K. Li, G.T. Liu, J.H. Xu, K. Wang, G.S. Luo, A microdevice for producing monodispersed droplets under a jetting flow, RSC Adv. 5 (35) (2015) 27356-27364
[38] C.F. Zhou, P.T. Yue, J.J. Feng, Formation of simple and compound drops in microfluidic devices, Phys. Fluids 18 (9) (2006) 092105
[39] C. Cramer, P. Fischer, E.J. Windhab, Drop formation in a co-flowing ambient fluid, Chem. Eng. Sci. 59 (15) (2004) 3045-3058
[40] P.B. Umbanhowar, V. Prasad, D.A. Weitz, Monodisperse emulsion generation via drop break off in a coflowing stream, Langmuir 16 (2) (2000) 347-351
[41] T. Thorsen, R.W. Roberts, F.H. Arnold, S.R. Quake, Dynamic pattern formation in a vesicle-generating microfluidic device, Phys Rev Lett 86 (18) (2001) 4163-4166
[42] Xu JH, Luo GS, Li SW, Chen GG, Shear force induced monodisperse droplet formation in a microfluidic device by controlling wetting properties, Lab Chip 6 (1) (2006) 131-136
[43] J. Husny, J.J. Cooper-White, The effect of elasticity on drop creation in T-shaped microchannels, J. Non-Newton. Fluid Mech. 137 (1-3) (2006) 121-136
[44] S.N. Ghadiali, D.P. Gaver, The influence of non-equilibrium surfactant dynamics on the flow of a semi-infinite bubble in a rigid cylindrical capillary tube, J. Fluid Mech. 478 (2003) 165-196
[45] W.L. Ong, J.S. Hua, B.L. Zhang, T.Y. Teo, J.L. Zhuo, N.T. Nguyen, N. Ranganathan, L. Yobas, Experimental and computational analysis of droplet formation in a high-performance flow-focusing geometry, Sensor Actuat. A:Phys. 138 (1) (2007) 203-212
[46] K. Wang, Y.C. Lu, C.P. Tostado, L. Yang, G.S. Luo, Coalescences of microdroplets at a cross-shaped microchannel junction without strictly synchronism control, Chem. Eng. J. 227 (2013) 90-96