压力保持系统中一口井的压力恢复分析

• TRANSPORT PHENOMENA & FLUID MECHANICS • 上一篇下一篇

压力保持系统中一口井的压力恢复分析

林加恩^a,b; 杨慧珠^a

^a Department of Engineering Mechanics, Tsinghua University, Beijing 100084, China
^b Petroleum Engineering Institute, Xi’an Petroleum University, Xi'an 710065,China

收稿日期:1900-01-01 修回日期:1900-01-01 出版日期:2007-02-28 发布日期:2007-02-28
通讯作者: 林加恩

Pressure buildup analysis using type curves for a well in a pressure-maintained system

LIN Jia'en^a,b; YANG Huizhu^a

^a Department of Engineering Mechanics, Tsinghua University, Beijing 100084, China ^b Petroleum Engineering Institute, Xi’an Petroleum University, Xi'an 710065,China

Received:1900-01-01 Revised:1900-01-01 Online:2007-02-28 Published:2007-02-28
Contact: LIN Jia'en

摘要/Abstract

摘要： The development and application of a new solution is demonstrated for the type-curve analysis and interpretation of well test data from a multiwell reservoir system of both production and injection wells with two-phase flow. The buildup type curves or buildup behavior could be obtained through the solution by using superposition. But a new outer boundary condition for variable pressure boundary must be introduced to obtain the correct pressure buildup solutions by superposition. A technique is shown to determine the deviation time from the infinite-acting semilog radial flow stabilization in the derivatives of pressure, which is calculated with respect to and plotted vs. shut-in time.
Field examples are given to illustrate the use of the proposed method for analyzing transient pressure data from a well located in a multi-well water-injection reservoir. An adaptive genetic algorithm-based method is used to match the pressure and pressure derivative data to estimate reservoir parameters. The validity and applicability of the proposed method are also demonstrated through the examples.

关键词: multi-well reservoir;pressure buildup;two-phase flow;type curve analysis

Abstract: The development and application of a new solution is demonstrated for the type-curve analysis and interpretation of well test data from a multiwell reservoir system of both production and injection wells with two-phase flow. The buildup type curves or buildup behavior could be obtained through the solution by using superposition. But a new outer boundary condition for variable pressure boundary must be introduced to obtain the correct pressure buildup solutions by superposition. A technique is shown to determine the deviation time from the infinite-acting semilog radial flow stabilization in the derivatives of pressure, which is calculated with respect to and plotted vs. shut-in time.
Field examples are given to illustrate the use of the proposed method for analyzing transient pressure data from a well located in a multi-well water-injection reservoir. An adaptive genetic algorithm-based method is used to match the pressure and pressure derivative data to estimate reservoir parameters. The validity and applicability of the proposed method are also demonstrated through the examples.

Key words: multi-well reservoir, pressure buildup, two-phase flow, type curve analysis

林加恩, 杨慧珠. 压力保持系统中一口井的压力恢复分析[J]. , DOI: .

LIN ,Jia'en, YANG ,Huizhu. Pressure buildup analysis using type curves for a well in a pressure-maintained system[J]. , DOI: .

参考文献

1    Ramey, H.J. Jr., Cobb, W.M., “A general pressure buildup theory for a well in a closed drainage area”, J. Petrol. Technol., 12, 1493—1505(1971).
2    Kumar, A., Ramey, H.J. Jr., “Well-test analysis for a well in a constant-pressure square”, SPEJ, 4, 107—16(1974).
3    Earloughe, R.C. Jr., Advance in Well Test Analysis, Monograph Series SPE, USA (1977).
4    Kumar, A., “Strengths of water drive or fluid injection from transient well test data”, J. Petrol. Technol., 11, 1497—1508(1977).
5    Lin, J.E., “Pressure buildup analysis for a well in a pres-sure-maintained system”，SPE 27421, Richardson, TX., USA (1993).
6    Lin, J.E., Practical Well Test Analysis, Petroleum Indus-try Publishing House, Beijing, 86—97(1996). (in Chi-nese)
7    Onur, M., Serra, K.V., Reynolds, A.C., “Analysis of pressure buildup data from a well in a multi-well system”, SPEFE, 101—110(1991).
8    Lin, J.E., Liu, W.N., Chen, Q.L., “Pressure buildup analysis for a well in a multi-well system”, Well Testing, 2(4), 51—57(1993). (in Chinese)
9    Lin, J.E., Liu, W.N., Chen, Q.L., “Practical application of the well-test-analysis theory of a multi-well water flood-ing system”, Petroleum Exploration and Development, 23(3), 58—63(1996). (in Chinese)
10    Lin, J.E., Yang, H.Z., “Analysis of two-phase flow pres-sure buildup data from a well in an infinite multi-well reservoir”，J. Hydrodyn. B, 17(4), 489—497(2005).
11    Lin, J.E., Yang, H.Z., “Pressure buildup analysis for a well in an closed, bounded multi-well reservoir”, Chin. J. Chem. Eng., 13(4), 441—450(2005).
12    Chu, W.C., Reynolds, A.C., Raghavan, R., “Pressure transient analysis of two-phase flow problems”, SPEFE, 5(7), 151—164(1986).
13    Dong, J.X., Zhai, Y.F., Yang, J., Zhao, C.S., “Determi-nation of injection-production ratio size by type-curve analysis”, SEP 57320, 1999 SPE Asia Pacific Conference, Kuala Lumpur, Malaysia (1999).
14    Yin, H.J., Liang, X., Jiang, Y.C., “Study on transient flow regularity in low permeability reservoirs with con-sideration of injection-production ratio”, Special Oil and Gas Reservoirs, 10(5), 32—34 (2003). (in Chinese)
15    Wang, Q.X., Huang, J.F., Yin, H.J., “Characteristics of transient pressure with threshold pressure gradient  and  injection-production ratio”, Oil Drilling & Production Technology, 25(6), 57—59(2003). (in Chinese)
16    Sun, H.D., Liu. L., Zhou, F.D., “Max effective hole mathematical model and exact solution for vommingled reservoir”, Chin. J. Chem. Eng., 11(5), 550—554(2003).
17    Yin, H.J., Zhai, Y.F., “An optimal well test analysis based on adaptive genetic algorithm”, Petrol. Sinica, 20(2), 51—56(1999). (in Chinese)
18    Stehfest, H., “Algorithm 368-numerical inversion of Laplace transforms”, Commun. ACM , 113, 47(1970).
19    Wu, L.Y., Hu, Y.D., Xu, D.M., Hua, B., “A genetic al-gorithm-based approach to scheduling of batch produc-tion with maximum profit”, Chin. J. Chem. Eng., 13(1), 68—73(2005).