Surface and structure characteristics of commercial K-Feldspar powders: Effects of temperature and leaching media

doi:10.1016/j.cjche.2018.11.016

摘要/Abstract

摘要： This study presents morphological and structural variations of K-Feldspar mineral after acid treatment. Both organic and inorganic acids such as C₂H₂O₄, HCl, HNO₃ and H₂SO₄ were employed for this purpose. Another aim of this study was to find an optimum experimental condition for iron (Fe) removal with a minimum damage on the structure of K-Feldspar in which high whiteness index is obtained. The effect of different parameters such as concentration, pH and temperature on the final structure of this mineral was investigated. To find out the chemical composition of powder, XRF was utilized. FTIR, XRD and SEM were employed to study the structure of mineral. Spectrophotometry was chosen to analyze whiteness index of powder after acid treatment. It was found that O—Al—O bond at 647 cm^-1 for H₂SO₄ and HNO₃ treated sample disappeared. However, HCl and C₂H₂O₄ were ineffective at this band. In addition, the results revealed an increase in K-Feldspar content, a decrease in Fe content, an increase in whiteness index and no significant structural change for C₂H₂O₄ leached sample. Whiteness index of 91% was obtained for C₂H₂O₄ leached sample with the pH of 2.5 to 3 at temperature of 50℃ and during 1 h.

关键词: K-Feldspar, Iron oxide, Organic and inorganic acids, FTIR

Abstract: This study presents morphological and structural variations of K-Feldspar mineral after acid treatment. Both organic and inorganic acids such as C₂H₂O₄, HCl, HNO₃ and H₂SO₄ were employed for this purpose. Another aim of this study was to find an optimum experimental condition for iron (Fe) removal with a minimum damage on the structure of K-Feldspar in which high whiteness index is obtained. The effect of different parameters such as concentration, pH and temperature on the final structure of this mineral was investigated. To find out the chemical composition of powder, XRF was utilized. FTIR, XRD and SEM were employed to study the structure of mineral. Spectrophotometry was chosen to analyze whiteness index of powder after acid treatment. It was found that O—Al—O bond at 647 cm^-1 for H₂SO₄ and HNO₃ treated sample disappeared. However, HCl and C₂H₂O₄ were ineffective at this band. In addition, the results revealed an increase in K-Feldspar content, a decrease in Fe content, an increase in whiteness index and no significant structural change for C₂H₂O₄ leached sample. Whiteness index of 91% was obtained for C₂H₂O₄ leached sample with the pH of 2.5 to 3 at temperature of 50℃ and during 1 h.

Key words: K-Feldspar, Iron oxide, Organic and inorganic acids, FTIR

Hamed Salimkhani, Tohid Joodi, Aidin Bordbar-Khiabani, Ali Motei Dizaji, Behnam Abdolalipour, Ali Azizi. Surface and structure characteristics of commercial K-Feldspar powders: Effects of temperature and leaching media[J]. 中国化学工程学报, 2020, 28(1): 307-317.

参考文献

[1] E. Bernardo, A. Dattoli, E. Bonomo, L. Esposito, E. Rambaldi, A. Tucci, Application of an industrial waste glass in glass-ceramic stoneware, Int. J. Appl. Ceram. Technol. 8(5) (2011) 1153-1162.
[2] Z. Wang, Q. Zhang, Y. Yao, Y. Jia, B. Xie, The extraction of potassium from K-feldspar ore by low temperature molten salt method, Chin. J. Chem. Eng. 26(4) (2018) 845-851.
[3] H. Salimkhani, E.A. Fesaghandis, Sh. Salimkhani, B. Abdolalipour, A.M. Dizaji, T. Joodi, A. Bordbar-Khiabani, In situ synthesis of leucite based feldspathic dental porcelain with minor Kalsilite and Fe₂O₃ impurities, Int. J. Appl. Ceram. Technol. 16(2019) 552-561.
[4] M. Awaad, S.M. Naga, N. El-Mehalawy, Effect of replacing weathered feldspar for potash feldspar in the production of stoneware tiles containing fish bone ash, Ceram. Int. 41(6) (2015) 7816-7822.
[5] J. Yuan, J. Yang, H. Ma, S. Su, Q. Chang, S. Komarneni, Hydrothermal synthesis of nano-kaolinite from K-feldspar, Ceram. Int. 44(13) (2018) 15611-15617.
[6] M.F. Zawrah, R.M. Khattab, A.A. El-Kheshen, E. El Fadaly, Sintering and properties of borosilicate glass/Li-Na-K-feldspar composites for electronic applications, Ceram. Int. 43(17) (2017) 15068-15073.
[7] A.A. El-Kheshen, M.F. Zawrah, E.M. Hamzawy, Development of low thermal expansion mono crystalline Sr-feldspar phase via Sr-cordierite ceramic/borosilicate glass composite, Ceram. Int. 44(12) (2018) 13720-13726.
[8] H.L. Alling, The mineralography of the feldspars. Part I, J. Geol. 29(3) (1921) 193-294.
[9] J.V. Smith, Feldspar Minerals:2 Chemical and Textural Properties, Springer Science & Business Media, 2012.
[10] T. Wajima, K. Munakata, Material conversion from waste sandstone cake into cation exchanger using alkali fusion, Ceram. Int. 38(2) (2012) 1741-1744.
[11] M.F. Brigatti, E. Galan, B.K.G. Theng, Structures and mineralogy of clay minerals, Dev. Clay Sci. 1(2006) 19-86.
[12] R.J. Ancnr, L.W. Frncnn, Structural variation associated with compositional variation and order-disorder behavior in anorthite-rich feldspars, Am. Mineral. 7(5) (1990) 150-162.
[13] W.D. Nesse, Introduction to Mineralogy, Oxford University Press, New York, 2012.
[14] F. Veglio, B. Passariello, C. Abbruzzese, Iron removal process for high-purity silica sands production by oxalic acid leaching, Ind. Eng. Chem. Res. 38(11) (1999) 4443-4448.
[15] I. Štyriaková, I. Štyriak, P. Malachovský, M. Lovás, Biological, chemical and electromagnetic treatment of three types of feldspar raw materials, Miner. Eng. 19(4) (2006) 348-354.
[16] L.L. Stillings, J.I. Drever, S.L. Brantley, Y. Sun, R. Oxburgh, Rates of feldspar dissolution at pH 3-7 with 0-8 mM oxalic acid, Chem. Geol. 132(1-4) (1996) 79-89.
[17] J. Bevan, D. Savage, The effect of organic acids on the dissolution of K-feldspar under conditions relevant to burial diagenesis, Mineral. Mag. 53(372) (1989) 415-425.
[18] R. Salmimies, M. Mannila, J. Juha, A. Häkkinen, Acidic dissolution of magnetite:Experimental study on the effects of acid concentration and temperature, Clay Clay Miner. 59(2) (2011) 136-146.
[19] B. Yuan, C. Li, B. Liang, L. Lü, H. Yue, H. Sheng, L. Ye, H. Xie, Extraction of potassium from K-feldspar via the CaCl₂ calcination route, Chin. J. Chem. Eng. 23(9) (2015) 1557-1564.
[20] B. Nayebi, M. Mehrabian, M. Shahedi Asl, M. Shokouhimehr, Nanostructural approach to the thickening behavior and oxidation of calcium-stabilized aluminum foams, Mater. Chem. Phys. 220(2018) 351-359.
[21] M. Akhlaghi, S.A. Tayebifard, E. Salahi, M. Shahedi Asl, G. Schmidt, Self-propagating high-temperature synthesis of Ti₃AlC₂ MAX phase from mechanically-activated Ti/Al/graphite powder mixture, Ceram. Int. 44(8) (2018) 9671-9678.
[22] S.M. Salaken, E. Farzana, J. Podder, Effect of Fe-doping on the structural and optical properties of ZnO thin films prepared by spray pyrolysis, J. Semicond. 34(7) (2013) (073003).
[23] W. Stumm, B. Sulzberger, The cycling of iron in natural environments:considerations based on laboratory studies of heterogeneous redox processes, Geochim. Cosmochim. Acta 56(8) (1992) 3233-3257.
[24] H. Salimkhani, P. Palmeh, A.B. Khiabani, E. Hashemi, S. Matinpour, H. Salimkhani, M.S. Asl, Electrophoretic deposition of spherical carbonyl iron particles on carbon fibers as a microwave absorbent composite, Surf. Interfaces 5(2016) 1-7.
[25] F. Movassagh-Alanagh, A. Bordbar Khiabani, H. Salimkhani, Improvement in magnetic and microwave absorption properties of nano-Fe₃O₄@CFs composites using a modified multi-step EPD process, Appl. Surf. Sci. 420(2017) 726-739.
[26] D. Panias, M. Taxiarchou, I. Paspaliaris, A. Kontopoulos, Mechanisms of dissolution of iron oxides in aqueous oxalic acid solutions, Hydrometallurgy 42(2) (1996) 257-265.
[27] M. Gholipourmalekabadi, S. Zhao, B.S. Harrison, M. Mozafari, A.M. Seifalian, Oxygengenerating biomaterials:a new, viable paradigm for tissue engineering? Trends Biotechnol. 34(12) (2016) 1010-1021.
[28] Z. Zamanipour, X. Shi, M. Mozafari, J.S. Krasinski, L. Tayebi, D. Vashaee, Synthesis, characterization, and thermoelectric properties of nanostructured bulk p-type MnSi1.73, MnSi1.75, and MnSi1.77, Ceram. Int. 39(3) (2013) 2353-2358.
[29] A. Bordbar-Khiabani, S. Ebrahimi, B. Yarmand, Plasma electrolytic oxidation of monocrystalline silicon using silicate electrolyte containing boric acid, Appl. Surf. Sci. 462(2018) 913-922.
[30] M. Shokouhimehr, Mohammadreza, M. Shahedi Asl, B. Mazinani, Modulated largepore mesoporous silica as an efficient base catalyst for the Henry reaction, Res. Chem. Intermed. 44(3) (2018) 1617-1626; D.M. González-García, L. Téllez-Jurado, F.J. Jiménez-Álvarez, H. Balmori-Ramírez, Structural study of geopolymers obtained from alkali-activated natural pozzolan feldspars, Ceram. Int. 43(2) (2017) 2606-2613.
[31] S. Aliramaji, A. Zamanian, M. Mozafari, Super-paramagnetic responsive silk fibroin/chitosan/magnetite scaffolds with tunable pore structures for bone tissue engineering applications, Mater. Sci. Eng. C 70(2017) 736-744.
[32] N.O. Dantas, W.E. Ayta, A.C. Silva, N.F. Cano, S.W. Silva, P.C. Morais, Effect of Fe₂O₃ concentration on the structure of the SiO₂-Na₂O-Al₂O₃-B₂O₃ glass system, Spectrochim. Acta A Mol. Biomol. Spectrosc. 81(1) (2011) 140-143.
[33] S. Singh, K. Singh, Effect of in-situ reduction of Fe³⁺ on physical, structural and optical properties of calcium sodium silicate glasses and glass ceramics, J. Non-Cryst. Solids 386(2014) 100-104.
[34] A. Haghighatzadeh, B. Mazinani, M. Shahedi Asl, L. Bakhtiari, TiO₂(rutile and anatase) deposited on ordered mesoporous SiO₂:Effect of pore size on photocatalytic activity, Desalin. Water Treat. 80(2017) 156-163.
[35] A. Bordbar-Khiabani, B. Yarmand, M. Mozafari, Functional PEO layers on magnesium alloys:Innovative polymer-free drug-eluting stents, Surf. Innov. 6(4-5) (2018) 237-243.
[36] E.O. Olanipekun, Kinetics of leaching laterite, Int. J. Miner. Process. 60(1) (2000) 9-14.
[37] D. Panias, M. Taxiarchou, I. Douni, I. Paspaliaris, A. Kontopoulos, Thermodynamic analysis of the reactions of iron oxides:Dissolution in oxalic acid, Can. Metall. Q. 35(4) (1996) 363-373.
[38] L. Lü, C. Li, G. Zhang, X. Hu, B. Liang, Decomposition behavior of CaSO₄ during potassium extraction from a potash feldspar-CaSO₄ binary system by calcination, Chin. J. Chem. Eng. 26(4) (2018) 838-844.
[39] A.E. Lavat, M.C. Grasselli, J.E. Tasca, Phase changes of ceramic whiteware slip-casting bodies studied by XRD and FTIR, Ceram. Int. 33(6) (2007) 1111-1117.
[40] L.O. Filippov, R. Joussemet, M. Irannajad, R. Houot, A. Thomas, An approach of the whiteness quantification of crushed and floated talc concentrate, Powder Technol. 105(1-3) (1999) 106-112.
[41] M. Shahedi Asl, B. Nayebi, Z. Ahmadi, M.J. Zamharir, M. Shokouhimehr, Effects of carbon additives on the properties of ZrB₂-based composites:A review, Ceram. Int. 44(7) (2018) 7334-7348.
[42] X. Wang, C. Li, H. Yue, S. Yuan, C. Liu, S. Tang, B. Liang, Effects of mechanical activation on the digestion of ilmenite in dilute H₂SO₄, Chin. J. Chem. Eng. (2018). https://doi.org/10.1016/j.cjche.2018.06.020.
[43] U. Schwertmann, Solubility and dissolution of iron oxides, Plant Soil 130(1-2) (1991) 1-25.
[44] H. Salehi, H. Aghajani, H. Salimkhani, Isothermal and kinetic studies on oxidation roasting of Kahnooj ilmenite concentrate, Chem. Eng. Trans. 66(2018) 397-402.
[45] H. Salimkhani, A.M. Dizaji, E. Hashemi, P. Palmeh, G. Sabeghi, S. Salimkhani, Magnetic and microwave absorptive properties of electrophoretically deposited nano-CoFe₂O₄ as a 3D structure on carbon fibers, Ceram. Int. 42(11) (2016) 12709-12714.
[46] X.U. Tao, L. Xiaoqin, Peanut shell activated carbon:Characterization, surface modification and adsorption of Pb²⁺ from aqueous solution, Chin. J. Chem. Eng. 16(3) (2008) 401-406.
[47] A. Hamlekhan, M. Mozafari, N. Nezafati, M. Azami, H. Hadipour, A proposed fabrication method of novel PCL-GEL-HAp nanocomposite scaffolds for bone tissue engineering applications, Adv. Compos. Lett. 19(4) (2010) 123-130.