Numerical and experimental study on the particle erosion and gas–particle hydrodynamics in an integral multi-jet swirling spout-fluidized bed

doi:10.1016/j.cjche.2023.03.011

中国化学工程学报 ›› 2023, Vol. 61 ›› Issue (9): 90-101.DOI: 10.1016/j.cjche.2023.03.011

• Full Length Article • 上一篇下一篇

Numerical and experimental study on the particle erosion and gas–particle hydrodynamics in an integral multi-jet swirling spout-fluidized bed

Wenbin Li¹, Feng Wu¹, Liuyun Xu¹, Jipeng Sun², Xiaoxun Ma¹

1. School of Chemical Engineering, Northwest University, Xi'an 710069, China;
2. Luoyang Jianguang Special Equipment Co., Ltd, Luoyang 471003, China

收稿日期:2022-12-24 修回日期:2023-03-12 出版日期:2023-09-28 发布日期:2023-12-14
通讯作者: Feng Wu,E-mail:wufeng@nwu.edu.cn
基金资助:
This work is supported by the National Natural Science Foundation of China (22178286) and Shaanxi Qin Chuangyuan “scientist and engineer” team construction project (2022KXJ-041).

Numerical and experimental study on the particle erosion and gas–particle hydrodynamics in an integral multi-jet swirling spout-fluidized bed

Wenbin Li¹, Feng Wu¹, Liuyun Xu¹, Jipeng Sun², Xiaoxun Ma¹

1. School of Chemical Engineering, Northwest University, Xi'an 710069, China;
2. Luoyang Jianguang Special Equipment Co., Ltd, Luoyang 471003, China

Received:2022-12-24 Revised:2023-03-12 Online:2023-09-28 Published:2023-12-14
Contact: Feng Wu,E-mail:wufeng@nwu.edu.cn
Supported by:
This work is supported by the National Natural Science Foundation of China (22178286) and Shaanxi Qin Chuangyuan “scientist and engineer” team construction project (2022KXJ-041).

摘要/Abstract

摘要： In this paper, using the computational fluid dynamics based on Euler Lagrange and the commercial software Barracuda VR, the gas–particle hydrodynamics and the erosion of particles on the inner wall and internal components of the spouted bed in the integrated multi-jet swirling spout-fluidized bed (IMSSFB) are studied. Erosion experiments have obtained the characterization of particle erosion on internal components and verified the relevant numerical models. The results show that: the particle distribution within the IMSSFB is uneven due to the cyclonic effect of the axial swirl vane (ASV), resulting in particle erosion for the ASV being concentrated on one side; when the gas reaches the top, too high an erosion gas velocity leads to gas backflow. As the filling height increases, there is a tendency for the erosion position of the particles on the ASV to expand upwards. However, the effect of increasing gas velocity on the erosion position is insignificant.

关键词: Integral multi-jet swirling spout-fluidized bed, Gas–particle hydrodynamics, Axial swirl vane, Uneven, Erosion

Abstract: In this paper, using the computational fluid dynamics based on Euler Lagrange and the commercial software Barracuda VR, the gas–particle hydrodynamics and the erosion of particles on the inner wall and internal components of the spouted bed in the integrated multi-jet swirling spout-fluidized bed (IMSSFB) are studied. Erosion experiments have obtained the characterization of particle erosion on internal components and verified the relevant numerical models. The results show that: the particle distribution within the IMSSFB is uneven due to the cyclonic effect of the axial swirl vane (ASV), resulting in particle erosion for the ASV being concentrated on one side; when the gas reaches the top, too high an erosion gas velocity leads to gas backflow. As the filling height increases, there is a tendency for the erosion position of the particles on the ASV to expand upwards. However, the effect of increasing gas velocity on the erosion position is insignificant.

Key words: Integral multi-jet swirling spout-fluidized bed, Gas–particle hydrodynamics, Axial swirl vane, Uneven, Erosion

Wenbin Li, Feng Wu, Liuyun Xu, Jipeng Sun, Xiaoxun Ma. Numerical and experimental study on the particle erosion and gas–particle hydrodynamics in an integral multi-jet swirling spout-fluidized bed[J]. 中国化学工程学报, 2023, 61(9): 90-101.

参考文献

[1] S. Zeng, B. Su, M.L. Zhang, Y. Gao, J. Liu, S. Luo, Q.M. Tao, Analysis and forecast of China’s energy consumption structure, Energy Policy 159 (2021) 112630.
[2] G.Z. Yin, B. Li, F. Natalie, H.G. Patricia, K. Daniel M., M.S. Duan, Orderly retire China’s coal-fired power capacity via capacity payments to support renewable energy expansion, iScience 24 (11) (2021) 103287.
[3] W.R. Zhang, M.J. Ren, J.J. Kang, Y.O. Zhou, Y.H. Yuan, Estimating stranded coal assets in China’s power sector, Utilities Policy 75 (2022) 101352.
[4] X.K. Li, J.R. Han, Y. Liu, Z.H. Dou, T.A. Zhang, Summary of research progress on industrial flue gas desulfurization technology, Sep. Purif. Technol. 281 (2022) 119849.
[5] Y. Yang, Y.T. Fan, H.L. Li, Y. Qi, W. Han, J.M. Dan, J.Y. Wang, Study on thermal decomposition process of semidry flue gas desulfurization ash, Energy Fuels 33 (9) (2019) 9023–9031.
[6] Í.W.L. França, S.J.M. Cartaxo, M. Bastos-Neto, L.R.B. Gonçalves, F.A.N. Fernandes, Effect of additives to improve calcium-based sorbents in semi-dry flue gas desulphurization, Emiss. Control Sci. Technol. 6 (1) (2020) 105–112.
[7] J.L. Du, K Yue, F Wu., X.X. Ma, Z.Q. Hui, Numerical investigation on the water vaporization during semi dry flue gas desulfurization in a three-dimensional spouted bed, Powder Technol. 383 (2021) 471–483.
[8] A. Rahimi, M.S. Hatamipour, M. Gholami, M.R. Haghnegahdar, Non-isothermal modeling of the flue gas desulphurization process using a semi-dry spouted bed reactor, Chem. Eng. Res. Des. 89 (6) (2011) 777–784.
[9] M. Ali Fakhari, A. Rahimi, M.S. Hatamipour, A. Fozooni, Non-isothermal modeling of simultaneous CO₂ and SO₂ removal in a semi-dry spouted bed reactor, Process. Saf. Environ. Prot. 98 (2015) 342–353.
[10] F. Wu, K Yue, W. Gao, M. Gong, X.X. Ma, W.J. Zhou, Numerical simulation of semi-dry flue gas desulfurization process in the powder–particle spouted bed, Adv. Powder Technol. 31 (1) (2020) 323–331.
[11] Q. Zhang, K.T. Gui, A novel semidry flue gas desulfurization process with the magnetically fluidized bed reactor, J. Hazard. Mater. 168 (2–3) (2009) 1341–1345.
[12] H. Qin, K. Yang, B.Z. Sun, Q. Wang, C.H. Xu, Y.Q. Qi, Experimental study on spouted bed hydrodynamics for oil shale semi-coke, Energy Procedia 17 (2012) 1740–1746.
[13] A. Niksiar, B. Nasernejad, Activated carbon preparation from pistachio shell pyrolysis and gasification in a spouted bed reactor, Biomass Bioenergy 106 (2017) 43–50.
[14] H. Boujjat, S. Rodat, S. Chuayboon, S. Abanades, Numerical simulation of reactive gas–particle flow in a solar jet spouted bed reactor for continuous biomass gasification, Int. J. Heat Mass Transf. 144 (2019) 118572.
[15] S.Y. Wang, L.Q. Zhao, C.S. Wang, Y.S. Liu, J.S. Gao, Y. Liu, Q.L. Cheng, Numerical simulation of gas–solid flow with two fluid model in a spouted-fluid bed, Particuology 14 (2014) 109–116.
[16] S. Ando, T. Maki, Y. Nakagawa, N. Namiki, H. Emi, Y. Otani, Analysis of the drying process of seed particles in a spouted bed with a draft tube, Adv. Powder Technol. 13 (1) (2002) 73–91.
[17] E.R. Monazam, R.W. Breault, J. Weber, K. Layfield, Minimum spouting velocity of flat-base spouted fluid bed, Particuology 36 (2018) 27–36.
[18] M. Saidi, H.B. Tabrizi, J.R. Grace, A review on pulsed flow in gas–solid fluidized beds and spouted beds: Recent work and future outlook, Adv. Powder Technol. 30 (6) (2019) 1121–1130.
[19] W. Gu, H.N. Li, S. Liu, Y. Zhou, Influence of a sound field on the flow pattern of hollow microbeads in a spout-fluidized bed with a draft tube, Powder Technol. 354 (2019) 211–217.
[20] Y.M. Zhang, G.Q. Huang, G.L. Su, Hydrodynamic behavior of silicon particles with a wide size distribution in a draft tube spout-fluid bed, Chem. Eng. J. 328 (2017) 645–653.
[21] S.H. Hosseini, M.J. Rezaei, M. Bag-Mohammadi, H. Altzibar, M. Olazar, Smart models to predict the minimum spouting velocity of conical spouted beds with non-porous draft tube, Chem. Eng. Res. Des. 138 (2018) 331–340.
[22] F. Wu, W.W. Gao, J.J. Zhang, X.X. Ma, W.J. Zhou, Numerical analysis of gas–solid flow in a novel spouted bed structure under the longitudinal vortex effects, Chem. Eng. J. 334 (2018) 2105–2114.
[23] F. Wu, C.L. Yang, X.X. Che, X.X. Ma, Y. Yan, W.J. Zhou, Numerical and experimental study of integral multi-jet structure impact on gas–solid flow in a 3D spout-fluidized bed, Chem. Eng. J. 393 (2020) 124737.
[24] L.Y. Zhou, Y.Z. Zhao, CFD-DEM simulation of fluidized bed with an immersed tube using a coarse-grain model, Chem. Eng. Sci. 231 (2021) 116290.
[25] K.K. Dwivedi, S. Dutta, C. Loha, M.K. Karmakar, P.K. Chatterjee, A numerical study on the wall erosion impact and gas–particle hydrodynamics in circulating fluidized bed riser, Therm. Sci. Eng. Prog. 22 (2021) 100852.
[26] J.H. Song, T. Wang, J. Gao, X.B. Xiao, C.Q. Dong, X.Y. Hu, Erosion in the rectangular biomass circulating fluidized bed, Adv. Mater. Res. 608-609 (2012) 214–219.
[27] Y.F. Liu, O. Hinrichsen, Numerical simulation of tube erosion in a bubbling fluidized bed with a dense tube bundle, Chem. Eng. Technol. 36 (4) (2013) 635–644.
[28] X.W. Cao, N. Xiong, J. Li, Z.Q. Xie, X.R. Zang, J. Bian, Experimental study on the erosion of pipelines under different load conditions, Fluid Dyn. Mater. Process. 18 (2) (2022) 233–241.
[29] M. Parsi, K. Najmi, F. Najafifard, S. Hassani, B. McLaury, S. Shirazi, A comprehensive review of solid particle erosion modeling for oil and gas wells and pipelines applications, J. Nat. Gas Sci. Eng. 21 (2014) 850–873.
[30] Y. Zhang, E.P. Reuterfors, B.S. McLaury, S.A. Shirazi, E.F. Rybicki, Comparison of computed and measured particle velocities and erosion in water and air flows, Wear 263 (1–6) (2007) 330–338.
[31] D. Timo, W. Tom, H. Stefan, MP-PIC simulation of circulating fluidized beds using an EMMS based drag model for Geldart B particles, Particuology 59 (2021) 76–90.
[32] Q.Y. Tu, Z. Luo, H.G. Wang, MP-PIC simulation of the gas–solid full-loop flow characteristics in a dual fluidized bed and validation with experimental data, Chem. Eng. J. 421 (2021) 129835.
[33] X.D. Liu, H. Zhang, H.R. Yang, Y. Zhang, J. Lyu, Validation and evaluation of the CPFD modeling of dense particle flow velocity: Taking particle flow around an obstacle as an example, Chem. Eng. J. 453 (2023) 139719.
[34] S.L. Yang, F.H. Fan, Y.G. Wei, J.H. Hu, H. Wang, S.H. Wu, Three-dimensional MP-PIC simulation of the steam gasification of biomass in a spouted bed gasifier, Energy Convers. Manag. 210 (2020) 112689.
[35] M.J. Andrews, P.J. O'Rourke, The multiphase particle-in-cell (MP-PIC) method for dense particulate flows, Int. J. Multiph. Flow 22 (2) (1996) 379–402.
[36] L.T. Fan, C.Y. Wen, Mechanics of semifluidization of single size particles in solid–liquid systems, AIChE J. 7 (4) (1961) 606–610.
[37] S. Dutta, C. Loha, P.K. Chatterjee, A.K. Sadhukhan, P. Gupta, Numerical investigation of gas–particle hydrodynamics in a vortex chamber fluidized bed, Adv. Powder Technol. 29 (12) (2018) 3357–3367.
[38] B.H. Lee, Y.H. Bae, K.M. Kim, Y. Jiang, Y.H. Ahn, C.H. Jeon, Application of the CPFD method to analyze the effects of bed material density on gas–particle hydrodynamics and wall erosion in a CFB boiler, Fuel 342 (2023) 127878.
[39] J. Xie, W.Q. Zhong, B.S. Jin, Y.J. Shao, Y.J. Huang, Eulerian–Lagrangian method for three-dimensional simulation of fluidized bed coal gasification, Adv. Powder Technol. 24 (1) (2013) 382–392.
[40] M. Sosnowski, J. Krzywanski, K. Grabowska, R. Gnatowska, Polyhedral meshing in numerical analysis of conjugate heat transfer, EPJ Web Conf. 180 (2018) 02096.
[41] M.H. Khan, M.A. Hussain, Z. Mansourpour, N. Mostoufi, N.M. Ghasem, E.C. Abdullah, CFD simulation of fluidized bed reactors for polyolefin production—A review, J. Ind. Eng. Chem. 20 (6) (2014) 3919–3946.
[42] R. Thapa, A. Frohner, G. Tondl, C. Pfeifer, B. Halvorsen, Circulating fluidized bed combustion reactor: Computational particle fluid dynamic model validation and gas feed position optimization, Comput. Chem. Eng. 92 (2016) 180–188.
[43] X.X. Che, F. Wu, X.X. Ma, Effect of adjusted mesoscale drag model on flue gas desulfurization in powder–particle spouted beds, Front. Chem. Sci. Eng. 16 (6) (2022) 909–920.

Numerical and experimental study on the particle erosion and gas–particle hydrodynamics in an integral multi-jet swirling spout-fluidized bed

Numerical and experimental study on the particle erosion and gas–particle hydrodynamics in an integral multi-jet swirling spout-fluidized bed

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价

[1]	M. Lavanya, V. Ramachandra Murthy, Padmalatha Rao. Erosion corrosion control of 6061 aluminum alloy in multi-phase jet impingement conditions with eco-friendly green inhibitor[J]. 中国化学工程学报, 2020, 28(2): 340-347.
[2]	姚军, 樊建人, 岑可法. 气固两相流中一种抗磨新方法的数值验证[J]. , 2002, 10(1): 93-101.
[3]	樊建人, 陈丽华, 张新育, 岑可法. Numerical simulation of the tube erosion resulted from particles impacts[J]. , 1997, 5(4): 337-346.