CFD simulation of bubbly turbulent Tayor-Couette flow

doi:10.1016/j.cjche.2016.01.013

Abstract

Abstract: Bubbly gas-liquid Taylor-Couette vortex flow has been the subject of several recent investigations both because of interest in bubble-induced drag reduction and because such devices have potential applications to a variety of chemical and biochemical processing problems. In order to quantitatively describe the hydrodynamics of highly turbulent two phase Taylor-Couette flow, a rigorous two-fluid computational fluid dynamics (CFD) model was developed and compared with previously published experimental data. This model includes a comprehensive description of the constitutive closure for inter-phase forces and turbulence was simulated using both the k-ε and k-ω models. In addition, the mechanism by which the dispersed fluid attains a non-uniform radial and axial distribution is analyzed and the relative importance of various interphase forces is discussed. Lastly the model was validated by comparison of simulation predictions with experimental data, and it is shown that the CFD model correctly predicts phase velocity, velocity fluctuation, and gas distribution, and may provide guidance for reactor design and scale-up.

Key words: Taylor-Couette flow, Two-phase flow, Bubble, CFD

摘要： Bubbly gas-liquid Taylor-Couette vortex flow has been the subject of several recent investigations both because of interest in bubble-induced drag reduction and because such devices have potential applications to a variety of chemical and biochemical processing problems. In order to quantitatively describe the hydrodynamics of highly turbulent two phase Taylor-Couette flow, a rigorous two-fluid computational fluid dynamics (CFD) model was developed and compared with previously published experimental data. This model includes a comprehensive description of the constitutive closure for inter-phase forces and turbulence was simulated using both the k-ε and k-ω models. In addition, the mechanism by which the dispersed fluid attains a non-uniform radial and axial distribution is analyzed and the relative importance of various interphase forces is discussed. Lastly the model was validated by comparison of simulation predictions with experimental data, and it is shown that the CFD model correctly predicts phase velocity, velocity fluctuation, and gas distribution, and may provide guidance for reactor design and scale-up.

关键词: Taylor-Couette flow, Two-phase flow, Bubble, CFD

Xi Gao, Bo Kong, R. Dennis Vigil. CFD simulation of bubbly turbulent Tayor-Couette flow[J]. Chin.J.Chem.Eng., 2016, 24(6): 719-727.

Xi Gao, Bo Kong, R. Dennis Vigil. CFD simulation of bubbly turbulent Tayor-Couette flow[J]. Chinese Journal of Chemical Engineering, 2016, 24(6): 719-727.

References

[1] C.D. Andereck, S.S. Liu, H.L. Swinney, Flow regimes in a circular Couette systemwith independently rotating cylinders, J. Fluid Mech. 164(1986) 155-183.

[2] A. Chouippe, E. Climent, D. Legendre, C. Gabillet, Numerical simulation of bubble dispersion in turbulent Taylor-Couette flow, Phys. Fluids 26(2014), 043304.

[3] S. Vedantam, J.B. Joshi, Annular centrifugal extractors:A review, Chem. Eng. Res. Des. 84(2006) 522-542.

[4] S. Vedantam, J.B. Joshi, S.B. Koganti, Three dimensional CFD simulation of stratified two-fluid Taylor-Couette flow, Can. J. Chem. Eng. 84(2006) 279-288.

[5] D.D. Joseph, K. Nguyen, G.S. Beavers, Non-uniqueness and stability of the configuration of flow of immiscible fluids with different viscosities, J. Fluid Mech. 141(1984) 319-345.

[6] Y. Renardy, D.D. Joseph, Couette flow of two fluids between concentric cylinders, J. Fluid Mech. 150(1985) 381-394.

[7] D.D. Joseph, L. Preziosi, Stability of rigid motions and coating films in bicomponent flows of immiscible liquids, J. Fluid Mech. 185(1987) 323-329.

[8] D.D. Joseph, P. Singh, K. Chen, Couette flows, rollers, emulsions, tall Taylor cells, phase separation and inversion, and a chaotic bubble in Taylor-Couette flow of two immiscible liquids, Nonlinear evolution of spatio-temporal structures in dissipative continuous systems, NATO ASI series, 2251990, pp. 169-189.

[9] X.Y. Zhu, R.D. Vigil, Banded liquid-liquid Taylor-Couette-Poiseuille flow, AICHE J. 47(2001) (1932-1940).

[10] X.Y. Zhu, R.J. Campero, R.D. Vigil, Axial mass transport in liquid-liquid Taylor-Couette-Poiseuille flow, Chem. Eng. Sci. 55(2000) 5078-5087.

[11] R.J. Campero, R.D. Vigil, Spatiotemporal patterns in liquid-liquid Taylor-Couette-Poiseuille flow, Phys. Rev. Lett. 79(1997) 3897-3900.

[12] R.J. Campero, R.D. Vigil, Flow patterns in liquid-liquid Taylor-Couette-Poiseuille flow, Chem. Res. 38(1999) 1094-1098.

[13] Y. Shiomi, S. Nakanishi, H. Kutsuna, CFD calculation for two-phase flowin concentric annulus with rotating inner cylinder, PHOENICS users conference proceedings, phoenix2000.

[14] K. Atkhen, J. Fontaine, J.E.Wesfreid, Highly turbulent couette-taylor bubbly flow patterns, J. Fluid Mech. 422(2000) 55-68.

[15] H. Djéridi, C. Gabillet, J.Y. Billard, Two-phase Couette-Taylor flow:Arrangement of the dispersed phase and effects on the flow structures, Phys. Fluids 16(2004) 128-139.

[16] H. Djéridi, J.F. Favé, J.Y. Billard, D.H. Fruman, Bubble capture and migration in Couette-Taylor flow, Exp. Fluids 26(1999) 233-239.

[17] A. Mehel, C. Gabillet, H. Djeridi, Bubble effect on the structures of weakly turbulent Couette-Taylor flow, J. Fluids Eng. 128(2006) 819-831.

[18] E. Climent, M. Simonnet, J. Magnaudet, Preferential accumulation of bubbles in Couette-Taylor flow patterns, Phys. Fluids 19(2007) 083301.

[19] Y. Murai, H. Oiwa, Y. Takeda, Frictional drag reduction in bubbly Couette-Taylor flow, Phys. Fluids 20(2008) 034101.

[20] G.J. Bernstein, D.E. Grosvenor, J.F. Lenc, N.M. Levitz, A high-capacity annular centrifugal contactor, Nucl. Technol. 20(1973) 200-202.

[21] B. Kong, J.V. Shanks, R.D. Vigil, Enhanced algal growth rate in a Taylor vortex reactor, Biotechnol. Bioeng. 110(2013) 2140-2149.

[22] B. Kong, R.D. Vigil, Light-limited continuous culture of Chlorella vulgaris in a Taylor vortex reactor, Environ. Prog. Sustainable Energy 32(2013) 884-890.

[23] Y. Murai, H. Oiwa, Y. Takeda, Bubble behavior in a vertical Taylor-Couette flow, J. Phys. Conf. Ser. 14(2005) 143-156.

[24] D.P.M. van Gils, D.N. Guzman, C. Sun, D. Lohse, The importance of bubble deformability for strong drag reduction in bubbly turbulent Taylor-Couette flow, J. Fluid Mech. 722(2013) 317-347.

[25] T.H. van den Berg, S. Luther, D.P. Lathrop, D. Lohse, Drag reduction in bubbly Taylor-Couette turbulence, Phys. Rev. Lett. 94(2005) 044501.

[26] S.L. Ceccio, Friction drag reduction of external flows with bubble and gas injection, Annu. Rev. Fluid Mech. 42(2010) 183-203.

[27] K. Sugiyama, E. Calzavarini, D. Lohse, Microbubbly drag reduction in Taylor-Couette flow in the wavy vortex regime, J. Fluid Mech. 608(2008) 21-41.

[28] X. Gao, B. Kong, R.D. Vigil, CFD investigation of bubble effects on Tayor-Couette flow patterns in the weakly turbulent vortex regime, Chem. Eng. J. 270(2015) 508-518.

[29] M. Ramezani, B. Kong, X. Gao, M.G. Olsen, R.D. Vigil, Experimental measurement of oxygen mass transfer and bubble size distribution in an air-water multiphase Taylor-Couette vortex bioreactor, Chem. Eng. J. 279(2015) 286-296.

[30] X. Gao, B. Kong, M. Ramezani, M.G. Olsen, R.D. Vigil, An adaptive model for gas-liquid mass transfer in a Taylor vortex reactor, Int. J. Heat Mass Transf. 91(2015) 433-445.

[31] P.R. Fenstermacher, H.L. Swinney, J.P. Gollub, Dynamical instabilities and the transition to chaotic Taylor vortex flow, J. Fluid Mech. 94(1979) 103-128.

[32] G.S. Lewis, H.L. Swinney, Velocity structure functions, scaling, and transitions in high-Reynolds-number Couette-Taylor flow, Phys. Rev. E 59(1999) 5457-5467.

[33] S.G. Huisman, Roeland C.A. van der Veen, C. Sun, D. Lohse, Multiple states in highly turbulent Taylor-Couette flow, Nat. Commun. 5(2014) 3820.

[34] D.P. Lathrop, J. Fineberg, H.L. Swinney, Transition to shear-driven turbulence in Couette-Taylor flow, Phys. Rev. A 46(1992) 6390-6405.

[35] S.S. Deshmukh, S. Vedantam, J.B. Joshi, S.B. Koganti, Performance evaluation of an electrochemical reactor used to reduce Cr(VI) from aqueous media applying CFD simulations, Ind. Eng. Chem. Res. 46(2007) 8343-8354.

[36] S.S. Deshmukh, J.B. Joshi, S.B. Koganti, Flow visualization and three-dimensional CFD simulation of the annular region of an annular centrifugal extractor, Ind. Eng. Chem. Res. 47(2008) 3677-3686.

[37] S.S. Deshmukh, M.J. Sathe, J.B. Joshi, S.B. Koganti, Residence time distribution and flow patterns in the single-phase annular region of annular centrifugal extractor, Ind. Eng. Chem. Res. 48(2009) 37-46.

[38] T.V. Tamhane, J.B. Joshi, U.K. Mudali, R. Natarajan, R.N. Patil, Axial mixing in annular centrifugal extractors, Chem. Eng. J. 2012(207-208) (2012) 462-472.

[39] T.V. Tamhane, J.B. Joshi, R.N. Patil, Performance of annular centrifugal extractors:CFD simulation of flow pattern, axial mixing and extraction with chemical reaction, Chem. Eng. Sci. 110(2014) 134-143.

[40] M.J. Sathe, S.S. Deshmukh, J.B. Joshi, S.B. Koganti, Computational fluid dynamics simulation and experimental investigation:study of two-phase liquid-liquid flow in a vertical Taylor-Couette contactor, Ind. Eng. Chem. Res. 49(2010) 14-28.

[41] S. Vedantam, J.B. Joshi, S.B. Koganti, CFD simulation of RTD and mixing in the annular region of a Taylor-Couette contactor, Ind. Eng. Chem. Res. 45(2006) 6360-6367.

[42] X. Gao, L.J. Wang, C. Wu, Y.W. Cheng, X. Li, Novel bubble-emulsion hydrodynamic model for gas-solid bubbling fluidized beds, Ind. Eng. Chem. Res. 52(2013) 10835-10844.

[43] L. Schiller, Z. Naumann, A drag coefficient correlation, Z. Ver. Deutsch. Ing. 77(1935) 318-320.

[44] D.A. Drew, R.T. Lahey, Analytical modeling of multiphase flow, in:M.C. Roco (Ed.), Particulate two-phase flow, Butterworth-Heinemann, Boston, MA 1993, pp. 509-566.

[45] A. Behzadi, R.I. Issa, H. Rusche, Modelling of dispersed bubble and droplet flow at high phase fractions, Chem. Eng. Sci. 674(2004) 759-770.

[46] S.P. Antal, R.T. Lahey, J.E. Flaherty, Analysis of phase distribution in fully developed laminar bubbly two-phase flow, Int. J. Multiphase Flow 17(1991) 635-652.

[47] P. Chen, M.P. Dudukovic, J. Sanyal, Three-dimensional simulation of bubble column flows with bubble coalescence and breakup, AICHE J. 51(2005) 696.

[48] Q.S. Huang, C. Yang, G.Z. Yu, Z.-S. Mao, CFD simulation of hydrodynamics and mass transfer in an internal airlift loop reactor using a steady two-fluid model, Chem. Eng. Sci. 65(2010) 5527-5536.

[49] S. Talvy, A. Cockx, A. Liné, Modeling hydrodynamics of gas-liquid airlift reactor, AICHE J. 53(2007) 335-353.

[50] D.C. Wilcox, Turbulence modeling for CFD, DCW Industries Inc., La Canada, California, 1998.

[51] D.P.M. van Gils, G.W. Bruggert, D.P. Lathrop, C. Sun, D. Lohse, The Twente turbulent Taylor-Couette (T³C) facility:Strongly turbulent (multi-phase) flow between independently rotating cylinders, Rev. Sci. Instrum. 82(2011) 025105.

[52] D.P.M. van Gils, Highly turbulent Taylor-Couette flow, University of Twente, Enschede, Netherlands, 2011(PhD thesis).

[53] S.V. Patankar, Numerical heat transfer and fluid flow, Hemisphere Publishing Corporation, 1980.

[54] F.R. Menter, Zonal two equation k-ω turbulence models for aerodynamic flows, AIAA Paper #93-2906, 24th Fluid Dynamics Conference, July, 1993.

[55] F.R. Menter, Two-equation eddy-viscosity turbulence models for engineering applications, AIAA J. 32(1994) 1598-1605.

[56] A. Tomiyama, I. Kataoka, I. ?un, T. Sakaguchi, Drag coefficients of single bubbles under normal and micro gravity conditions, JSME Int. J. 42(1998) 472-498.

[57] D. Ma, G.J. Ahmadi, A thermodynamical formulation for dispersed turbulent flows-1:basic theory, Int. J. Multiphase Flow 16(1990) 323-340.

[58] D.Z. Zhang,W.B. Vanderheyden, The effects of mesoscale structures on the disperse two-phase flows and their closures for dilute suspensions, Int. J. Multiphase Flow 28(2002) 805-822.

[59] M.J. Burin, E. Schartman, H. Ji, Local measurements of turbulent angular momentum transport in circular Couette flow, Exp. Fluids 48(2010) 763-769.