Economic and entropy production evaluation of extractive distillation and solvent-assisted pressure-swing distillation by multi-objective optimization

doi:10.1016/j.cjche.2023.04.017

摘要/Abstract

摘要： Extractive distillation (ED) and solvent-assisted pressure-swing distillation (SA-PSD) are both special distillation processes that perform good at separating pressure-insensitive azeotropes. However, few reported studies have compared the performance of the two processes. In this paper, ED processes with N-methylpyrrolidone (NMP) and dimethlac-etamide (DMCA) as entrainer, SA-PSD process with isopropyl-alcohol (IPA) as solvent and SA-PSD process with partial heat integration (PHI-PSD) are proposed to achieve high purity separation of a mixture of cyclohexane/2-butanol system. The optimal operating conditions of the processes are obtained after optimizing with NSGA-II algorithm when total annual cost (TAC) and the entropy production of process are set as objectives. The optimal results show that the optimal PHI-PSD process has lower TAC by 28.7% and the lower entropy production by 39.5% than the optimal SA-PSD process while the ED process with NMP as entrainer has lower TAC by 50.9% and the lower entropy production by 56.1% than the optimal SA-PSD process. The optimal results show that the ED process with NMP as entrainer has the best economic and thermodynamic efficiency among the four proposed processes in this paper.

关键词: Extractive distillation, Solvent-assisted pressure-swing distillation, Entropy production, NSGA-II algorithm, Computer simulation

Abstract: Extractive distillation (ED) and solvent-assisted pressure-swing distillation (SA-PSD) are both special distillation processes that perform good at separating pressure-insensitive azeotropes. However, few reported studies have compared the performance of the two processes. In this paper, ED processes with N-methylpyrrolidone (NMP) and dimethlac-etamide (DMCA) as entrainer, SA-PSD process with isopropyl-alcohol (IPA) as solvent and SA-PSD process with partial heat integration (PHI-PSD) are proposed to achieve high purity separation of a mixture of cyclohexane/2-butanol system. The optimal operating conditions of the processes are obtained after optimizing with NSGA-II algorithm when total annual cost (TAC) and the entropy production of process are set as objectives. The optimal results show that the optimal PHI-PSD process has lower TAC by 28.7% and the lower entropy production by 39.5% than the optimal SA-PSD process while the ED process with NMP as entrainer has lower TAC by 50.9% and the lower entropy production by 56.1% than the optimal SA-PSD process. The optimal results show that the ED process with NMP as entrainer has the best economic and thermodynamic efficiency among the four proposed processes in this paper.

Key words: Extractive distillation, Solvent-assisted pressure-swing distillation, Entropy production, NSGA-II algorithm, Computer simulation

Yao Wang, Qing Ye, Jinlong Li, Qingqing Rui, Azhi Yu. Economic and entropy production evaluation of extractive distillation and solvent-assisted pressure-swing distillation by multi-objective optimization[J]. 中国化学工程学报, 2023, 63(11): 246-259.

参考文献

[1] D. Penner, C. Redepenning, A. Mitsos, J. Viell, Conceptual design of methyl ethyl ketone production via 2, 3-butanediol for fuels and chemicals, Ind. Eng. Chem. Res. 56 (14) (2017) 3947–3957.
[2] A. Romero, P. Yustos, A. Santos, Dehydrogenation of cyclohexanol to cyclohexanone: Influence of methylcyclopentanols on the impurities obtained in ε-caprolactam, Ind. Eng. Chem. Res. 42 (16) (2003) 3654–3661.
[3] Y.C. Chen, K.L. Li, C.L. Chen, I.L. Chien, Design and control of a hybrid extraction–distillation system for the separation of pyridine and water, Ind. Eng. Chem. Res. 54 (31) (2015) 7715–7727.
[4] Y. Cui, Z.S. Zhang, X.J. Shi, C. Guang, J. Gao, Triple-column side-stream extractive distillation optimization via simulated annealing for the benzene/isopropanol/water separation, Sep. Purif. Technol. 236 (2020) 116303.
[5] Y.Y. Shen, Q. Zhao, H.Y. Li, X.Y. Liu, Z.R. Chen, Z.Y. Zhu, P.Z. Cui, Y.X. Ma, Y.L. Wang, Design and optimization of reactive dividing-wall extractive distillation process for dimethyl carbonate synthesis based on quantum chemistry and molecular dynamics calculation, Sep. Purif. Technol. 273 (2021) 118978.
[6] I.D. Gil, D.C. Botía, P. Ortiz, O.F. Sánchez, Extractive distillation of acetone/methanol mixture using water as entrainer, Ind. Eng. Chem. Res. 48 (10) (2009) 4858–4865.
[7] L.M. Li, Y.Q. Tu, L.Y. Sun, Y.F. Hou, M.Y. Zhu, L.J. Guo, Q.S. Li, Y.Y. Tian, Enhanced efficient extractive distillation by combining heat-integrated technology and intermediate heating, Ind. Eng. Chem. Res. 55 (32) (2016) 8837–8847.
[8] C. Wang, Y. Zhuang, Y.C. Dong, L.L. Liu, L. Zhang, J. Du, Conceptual design of sustainable extractive distillation processes combining preconcentration and extractive distillation functions for separating ternary multi-azeotropic mixture, Chem. Eng. Sci. 263 (2022) 118088.
[9] Y.D. Chaniago, M. Lee, Distillation design and optimization of quaternary azeotropic mixtures for waste solvent recovery, J. Ind. Eng. Chem. 67 (2018) 255–265.
[10] W.L. Luyben, Methanol/trimethoxysilane azeotrope separation using pressure-swing distillation, Ind. Eng. Chem. Res. 53 (13) (2014) 5590–5597.
[11] Y.L. Wang, H.R. Zhang, X. Yang, Y.Y. Shen, Z.R. Chen, P.Z. Cui, L. Wang, F.Q. Meng, Y.X. Ma, J. Gao, Insight into separation of azeotrope in wastewater to achieve cleaner production by extractive distillation and pressure-swing distillation based on phase equilibrium, J. Clean. Prod. 276 (2020) 124213.
[12] W.L. Luyben, Comparison of extractive distillation and pressure-swing distillation for acetone–methanol separation, Ind. Eng. Chem. Res. 47 (8) (2008) 2696–2707.
[13] Z.Y. Zhu, S.H. Li, Y. Dai, X. Yang, Y.L. Wang, J. Gao, Control of a pressure-swing distillation process for benzene/isopropanol/water separation with and without heat integration, Sep. Purif. Technol. 236 (2020) 116311.
[14] Y.Y. Jiao, M. Yan, X.L. Wang, J.H. Zhong, Y.S. Chen, W.G. Zhu, X. Li, Z.Y. Zhu, P.Z. Cui, Y.Y. Lu, Y.L. Wang, Economic, environmental, energy and exergy analysis and multi-objective optimization for efficient purification of a friendly gasoline additive by extractive distillation coupled with pervaporation, Fuel 335 (2023) 127069.
[15] J.P. Knapp, M.F. Doherty, A new pressure-swing-distillation process for separating homogeneous azeotropic mixtures, Ind. Eng. Chem. Res. 31 (1) (1992) 346–357.
[16] W.S. Li, L. Shi, B.R. Yu, M. Xia, J.W. Luo, H.C. Shi, C.J. Xu, New pressure-swing distillation for separating pressure-insensitive maximum boiling azeotrope via introducing a heavy entrainer: Design and control, Ind. Eng. Chem. Res. 52 (23) (2013) 7836–7853.
[17] Y.T. Qin, Y. Zhuang, C. Wang, L. Zhang, L.L. Liu, J. Du, Multi-objective optimization and comparison of the entrainer-assisted pressure-swing distillation and extractive distillation separation sequences for separating a pressure-insensitive binary azeotrope, Comput. Chem. Eng. 165 (2022) 107959.
[18] Y. Li, C.J. Xu, Pressure-swing distillation for separating pressure-insensitive minimum boiling azeotrope methanol/toluene via introducing a light entrainer: Design and control, Ind. Eng. Chem. Res. 56 (14) (2017) 4017–4037.
[19] Y.S. Dai, X.Y. Zhou, X.J. Chu, C. Li, Z.H. Su, Z.Y. Zhu, P.Z. Cui, J.G. Qi, Y.L. Wang, Effect of entrainer thermodynamic properties on the separation of ternary mixtures containing two minimum boiling azeotropes by extractive distillation, Ind. Eng. Chem. Res. 61 (41) (2022) 15273–15288.
[20] G. Modla, P. Láng, Á. Kopasz, Entrainer selection for pressure swing batch distillation, Comput. Aided Chem. Eng., 25 (2008) 3-5.
[21] Y.D. Li, T.Y. Sun, Q. Ye, Y.G. Xu, X. Jian, J.L. Li, Investigation on energy-efficient extractive distillation for the recovery of ethyl acetate and 1, 4-dioxane from industrial effluent, J. Clean. Prod. 329 (2021) 129759.
[22] Y.G. Xu, J.L. Li, Q. Ye, Y.D. Li, Energy efficient extractive distillation process assisted with heat pump and heat integration to separate acetonitrile/1, 4-dioxane/water, Process. Saf. Environ. Prot. 156 (2021) 144–159.
[23] Y. Cui, X.J. Shi, C. Guang, Z.S. Zhang, C. Wang, C. Wang, Comparison of pressure-swing distillation and heterogeneous azeotropic distillation for recovering benzene and isopropanol from wastewater, Process. Saf. Environ. Prot. 122 (2019) 1–12.
[24] Q.Q. Rui, Q. Ye, J.L. Li, Y. Wang, A.Z. Yu, Investigation on energy-saving extractive distillation for recovering ethanol and 1, 4-dioxane from wastewater, Process. Saf. Environ. Prot. 170 (2023) 498–512.
[25] H.R. Zhang, S. Wang, J.X. Tang, N.N. Li, Y.N. Li, P.Z. Cui, Y.L. Wang, S.Q. Zheng, Z.Y. Zhu, Y.X. Ma, Multi-objective optimization and control strategy for extractive distillation with dividing-wall column/pervaporation for separation of ternary azeotropes based on mechanism analysis, Energy 229 (2021) 120774.
[26] J.A. Vázquez-Castillo, J.G. Segovia-Hernández, J.M. Ponce-Ortega, Multiobjective optimization approach for integrating design and control in multicomponent distillation sequences, Ind. Eng. Chem. Res. 54 (49) (2015) 12320–12330.
[27] F. Zhao, Z.F. Xu, J.G. Zhao, J. Wang, M.Y. Hu, X. Li, Z.Y. Zhu, P.Z. Cui, Y.L. Wang, Y.X. Ma, Process design and multi-objective optimization for separation of ternary mixtures with double azeotropes via integrated quasi-continuous pressure-swing batch distillation, Sep. Purif. Technol. 276 (2021) 119288.
[28] G. Miao, K.S. Zhuo, G.Q. Li, J. Xiao, An advanced optimization strategy for enhancing the performance of a hybrid pressure-swing distillation process in effective binary-azeotrope separation, Sep. Purif. Technol. 282 (2022) 120130.
[29] A. Yang, L. Ernawati, M. Wang, Z.Y. Kong, J. Sunarso, S.R. Sun, W.F. Shen, Multi-objective optimization of the intensified extractive distillation with side-reboiler for the recovery of ethyl acetate and methanol from wastewater, Sep. Purif. Technol. 310 (2023) 123131.
[30] K. Deb, A. Pratap, S. Agarwal, T. Meyarivan, A fast and elitist multiobjective genetic algorithm: NSGA-II, IEEE Trans. Evol. Computat. 6 (2) (2002) 182–197.
[31] S.R. Pandit, A.K. Jana, Transforming conventional distillation sequence to dividing wall column: Minimizing cost, energy usage and environmental impact through genetic algorithm, Sep. Purif. Technol. 297 (2022) 121437.
[32] J.L. Yan, J.Y. Liu, J.Y. Ren, Y. Wu, X.N. Li, T. Sun, L.Y. Sun, Design and multi-objective optimization of hybrid reactive-extractive distillation process for separating wastewater containing benzene and isopropanol, Sep. Purif. Technol. 290 (2022) 120915.
[33] B. Mondal, G.P. Rangaiah, A.K. Jana, Optimizing algal biodiesel production from a novel reactive distillation based unit: Reducing CO₂ emission and cost, Chem. Eng. Process. Process. Intensif. 176 (2022) 108948.
[34] Q. Zhao, Y.N. Li, C. Li, M. Yan, Z.Y. Zhu, P.Z. Cui, J.G. Qi, Y.L. Wang, C.X. Wang, Molecular dynamics-assisted process design and multi-objective optimization for efficient production of N-butyl acetate by reactive-extractive distillation/pervaporation, Sep. Purif. Technol. 296 (2022) 121427.
[35] C. Gutiérrez-Antonio, A. Briones-Ramírez, Pareto front of ideal Petlyuk sequences using a multiobjective genetic algorithm with constraints, Comput. Chem. Eng. 33 (2) (2009) 454–464.
[36] H. Benyounes, W.F. Shen, V. Gerbaud, Entropy flow and energy efficiency analysis of extractive distillation with a heavy entrainer, Ind. Eng. Chem. Res. 53 (12) (2014) 4778–4791.
[37] H.R. Zhang, F. Zhao, Z.Y. Ma, X.Y. Liu, P.Z. Cui, J. Gao, Y.L. Wang, S.Q. Zheng, Design and optimization for the separation of cyclohexane-isopropanol-water using mixed extractants with thermal integration based on molecular mechanism, Sep. Purif. Technol. 266 (2021) 118541.
[38] P.Z. Cui, F. Zhao, D. Yao, Z.Y. Ma, S.H. Li, X. Li, L. Wang, Z.Y. Zhu, Y.L. Wang, Y.X. Ma, D.M. Xu, Energy-saving exploration of mixed solvent extractive distillation combined with thermal coupling or heat pump technology for the separation of an azeotrope containing low-carbon alcohol, Ind. Eng. Chem. Res. 59 (29) (2020) 13204–13219.
[39] W.L. Luyben, Distillation Design and Control Using Aspen Simulation, Wiley, New York, 2006.