Single-jet Spray Mixing with a Confined Crossflow

doi:10.1016/S1004-9541(13)60436-X

摘要/Abstract

摘要： In order to achieve uniform mixing between spray droplets and crossflow, cold-model experiment of a hollow-cone water spray in an air crossflow is investigated via a numerical simulation. The simulation cases are designed by using the orthogonal design method. The Eulerian-Lagrangian formulation is employed for modeling the droplets-crossflow two-phase flow while the realizable k-ε turbulence model is used to describe the turbulence. A new index, mixedness quality, is proposed to assess the overall mixing of the droplets in the crossflow. The simulation results demonstrate that the counter-rotating vortex pair (CVP) imposes a more significant impact on the spatial distribution than on the size distribution of the droplets. Pairs of CVP with smaller scales are preferable for achieving a better mixing. The influencing factors are listed in the following order in terms of the degree of their impact from the greatest to the least: the Sauter diameter of the initial droplets, the mixing tube diameter, the spray angle, the velocity of the inlet crossflow, and the vertical velocity of the initial droplets. A moderate droplet diameter, a smaller tube diameter, a moderate spray angle, a greater crossflow velocity and a moderate vertical velocity of the droplet are favorable for achieving a higher mixedness quality of the jet spray in a confined crossflow.

关键词: mixing, jet spray droplets, crossflow, numerical simulation

Abstract: In order to achieve uniform mixing between spray droplets and crossflow, cold-model experiment of a hollow-cone water spray in an air crossflow is investigated via a numerical simulation. The simulation cases are designed by using the orthogonal design method. The Eulerian-Lagrangian formulation is employed for modeling the droplets-crossflow two-phase flow while the realizable k-ε turbulence model is used to describe the turbulence. A new index, mixedness quality, is proposed to assess the overall mixing of the droplets in the crossflow. The simulation results demonstrate that the counter-rotating vortex pair (CVP) imposes a more significant impact on the spatial distribution than on the size distribution of the droplets. Pairs of CVP with smaller scales are preferable for achieving a better mixing. The influencing factors are listed in the following order in terms of the degree of their impact from the greatest to the least: the Sauter diameter of the initial droplets, the mixing tube diameter, the spray angle, the velocity of the inlet crossflow, and the vertical velocity of the initial droplets. A moderate droplet diameter, a smaller tube diameter, a moderate spray angle, a greater crossflow velocity and a moderate vertical velocity of the droplet are favorable for achieving a higher mixedness quality of the jet spray in a confined crossflow.

Key words: mixing, jet spray droplets, crossflow, numerical simulation

孙慧娟, 白博峰, 严俊杰, 张海滨 . Single-jet Spray Mixing with a Confined Crossflow[J]. Chinese Journal of Chemical Engineering, DOI: 10.1016/S1004-9541(13)60436-X.

SUN Huijuan, BAI Bofeng, YAN Junjie, ZHANG Haibin . Single-jet Spray Mixing with a Confined Crossflow[J]. Chin.J.Chem.Eng., DOI: 10.1016/S1004-9541(13)60436-X.

参考文献

1 Lee, W.W., “Launching projectiles with hydrogen gas generated from aluminum fuel powder/water reactions”, U. S. Pat., 5052272 (1991).

2 Oh, H.W., Yoon, E.S., Kim, K.S., Ahn, J.W., “A practical approach to the hydraulic design and performance analysis of a mixed-flow pump for marine waterjet propulsion”, Proc. IMechE A J. Power Energy, 217 (6), 659-664 (2003).

3 Foote, J.P., Lineberry, J.T., Thompson, B.R., Winkelman, B.C., “Investigation of aluminum particle combustion for underwater propulsion applications”, AIAA Paper 96-3086 (1996).

4 Miller, T.F., Herr, J.D., “Green rocket propulsion by reaction of Al and Mg powders and water”, AIAA Paper 2004-4037 (2004).

5 Risha, G.A., Huang, Y., Yetter, R.A., Yang, V., Son, S.F., Tappan, B.C., “Combustion of aluminum particles with steam and liquid water”, AIAA Paper 2006-1154 (2006).

6 Miller, T.F., Garza, A.B., “Finite rate calculations of magnesium combustion in vitiated oxygen and steam atmospheres”, AIAA Paper 2006-4066 (2006).

7 Bartlett, H., Whalley, R., Rizvi, S.S.I., “Hybrid modelling, simulation and torque control of a marine propulsion system”, Proc. IMechE I J. Systems Control Eng., 213 (1), 1-10 (1999).

8 Tahsini, A.M., Ebrahimi, M., “Increasing Isp by injecting water into combustion chamber of an underwater SRM”, AIAA Paper 2006-4959 (2006).

9 Yang, Y., He, M., “A theoretical investigation of thermodynamic performance for a ramjet based on a magnesium-water reaction”, Proc. IMechE M J. Eng. Maritime Environ., 224 (1), 61-72 (2010).

10 Huang, L.Y., Xia, Z.X., Hu, J.X., Zhu, Q.W., “Performance study of a water ramjet engine”, Sci. China E, 54 (4), 877-882 (2011).

11 Liscinsky, D.S., True, B., Holdeman, J.D., “Mixing characteristics of directly opposed rows of jets injected normal to a crossflow in a rectangular duct”, AIAA Paper 94-0217 (1994).

12 Doerr, Th., Blomeyer, M., Hennecke, D.K., “Optimization of multiple jets mixing with a confined crossflow”, J. Eng. Gas Turbines Power, 119 (2), 315-321 (1997).

13 Everson, R., Manin, D., Sirovich, L., Winter, M., “Quantification of mixing and mixing rate from experimental observations”, AIAA J., 36 (2), 121-127 (1998).

14 Inamura, T., Nagai, N., “Spray characteristics of liquid jet traversing subsonic airstreams”, J. Propul. Power, 13 (2), 250-256 (1997).

15 Elshamy, O.M., Tambe, S.B., Cai, J., Jeng, S.M., “PIV and LDV measurements for liquid jets in crossflow”, AIAA Paper 2007-1338 (2007).

16 Kim, W., Yoon, W., “Spray characteristics of a pressure swirl nozzle under an atmospheric condition due to flash boiling”, AIAA Paper 2011-201 (2011).

17 Lin, J.Z., Qian, L.J., Xiong, H.B., “Relationship between deposition properties and operating parameters for droplet onto surface in the atomization impinging spray”, Powder Technol., 191 (3), 340-348 (2009).

18 Im, K.S., Lin, K.C., Lai, M.C., “Spray atomization of liquid jet in supersonic cross flows”, AIAA Paper 2005-732 (2005).

19 Lubarsky, E., Reichel, J.R., Zinn, B.T., McAmis, R., “Spray in crossflow: Dependence on Weber number”, J. Eng. Gas Turbines Power, 132 (2), Paper No. 021501 (2010).

20 Miller, P.C.H., Hadfield, D.J., “A simulation model of the spray drift from hydraulic nozzles”, J. Agric. Eng. Res., 42 (2), 135-147 (1989).

21 Holterman, H.J., van de Zande, J.C., Porskamp, H.A.J., Huijsmans, J.F.M., “Modelling spray drift from boom sprayers”, Comput. Electron Agr., 19 (1), 1-22 (1997).

22 Farooq, M., Balachandar, R., Wulfsohn, D., Wolf, T.M., “Agricultural sprays in cross-flow and drift”, J. agric. Engng. Res., 78 (4), 347-358 (2001).

23 Sureshkumar, R., Kale, S.R., Dhar, P.L., “Heat and mass transfer processes between a water spray and ambient air (II) Simulations”, Appl. Therm. Eng., 28 (5-6), 361-371 (2008).

24 Li, T.W., Pougatch, K., Salcudean, M., Grecov, D., “Numerical modeling of an evaporative spray in a riser”, Powder Technol., 201 (3), 213-229 (2010).

25 Uthuppan, J., Aggarwal, S.K., Grinstein, F.F., Kailasanath, K., “Particle dispersion in a transitional axisymmetric jet: A numerical simulation”, AIAA J., 32 (10), 2004-2014 (1994).

26 Ghosh, S., Hunt, J.C.R., “Spray jets in a cross-flow”, J. Fluid Mech., 365, 109-136 (1998).

27 Ariyapadi, S., Berruti, F., Balachandar, R., “Effect of cross flow on the spray characteristics of an industrial feed nozzle”, Chem. Eng. Comm., 190 (12), 1681-1704 (2003).

28 Shi, H., Kleinstreuer, C., “Simulation and analysis of high-speed droplet spray dynamics”, J. Fluids Eng., 129 (5), 621-633 (2007).

29 Nouri, J.M., Whitelaw, J.H., “Gasoline sprays in uniform crossflow”, Atomization Spray, 17 (7), 621-640 (2007).

30 Ruff, G.A., Sagar, A.D., Faeth, G.M., “Structure and mixing properties of pressure-atomized sprays”, AIAA J., 27 (7), 901-908 (1989).

31 Qian, L.J., Lin, J.Z., Xiong, H.B., “Simulation of droplet-gas flow in the effervescent atomization spray with an impinging plate”, Chin. J. Chem. Eng., 17 (1), 8-19 (2009).

32 Lin, J.Z., Qian, L.J., Xiong, H.B., Chan, T.L., “Effects of operating conditions on droplet deposition onto surface of atomization impinging spray”, Surf. Coat. Technol., 203 (12), 1733-1740 (2009).

33 Bai, B.F., Zhang, H.B., Liu, L., Sun, H.J., “Experimental study on turbulent mixing of spray droplets in crossflow”, Exp. Therm. Fluid Sci., 33 (6), 1012-1020 (2009).

34 Herrmann, M., “The influence of density ratio on the primary atomization of a turbulent liquid jet in crossflow”, Proc. Combust. Inst., 33 (2), 2079-2088 (2011).

35 Bai, B.F., Sun, H.J., Zhang, H.B., Liu, L., “Numerical study on turbulent mixing of spray droplets in crossflow”, J. Propul. Power, 27 (1), 132-143 (2011).

36 Schmidt, D.P., Nouar, I., Senecal, P.K., Rutland, C.J, Martin, J.K, Reitz, R.D., Hoffman, J.A., “Pressure-swirl atomization in the near field”, SAE-1999-01-0496 (1999).

37 O’Rourke, P.J., Amsden, A.A., “The TAB method for numerical calculation of spray droplet breakup”, SAE-872089 (1987).

38 O’Rourke, P.J., “Statistical properties and numerical implementation of a model for droplet dispersion in turbulent gas”, J. Comput. Phys., 83 (2), 345-360 (1989).

39 Crowe, C.T., Troutt, T.R., Chung, J.N., “Numerical models for two-phase turbulent flows”, Annu. Rev. Fluid Mech., 28, 11-43 (1996).

40 Stanton, D.W., Rutland, C.J., “Modeling fuel film formation and wall interaction in diesel engines”, SAE-960628 (1996).

41 Bai, C., Gosman, A.D., “Development of methodology for spray impingement simulation”, SAE-950283 (1995).

42 Li, Y.F., Yan, X.H., Jiang, G.F., Liu, Q., Song, J.X., Guo, C.C., “Toluene oxyfunctionalization with air over metalloporphyrins and reaction condition optimization”, Chin. J. Chem. Eng., 15 (3), 453-457 (2007).

43 Fan, J., Zhan, H.Y., “Optimization of synthesis of spherical lignosulphonate resin and its structure characterization”, Chin. J. Chem. Eng., 16 (3), 407-410 (2008).

44 Liu, L., Zhang, H.B., Sun, H.J., Bai, B.F., “Turbulent mixing flow structure of spray droplets in crossflow”, In: Proceedings of the 6th International Symposium on Multiphase Flow, Heat Mass Transfer and Energy Conversion, Guo, L.J., Chen, X.J., Lin, Z.H., eds., Xi’an Jiaotong University Press, Xi’an, China (2009).

[1]	Jiahao Xing, Huaizhi Han, Ruitian Yu, Wen Luo. Numerical simulation of flow and heat transfer of n-decane in sub-millimeter spiral tube at supercritical pressure[J]. 中国化学工程学报, 2023, 60(8): 173-185.
[2]	Mingzhi Li, Zhikai Liu, Wang Yao, Chao Xu, Yangping Yu, Mei Yang, Guangwen Chen. Ultrasonic cavitation-enabled microfluidic approach toward the continuous synthesis of cesium lead halide perovskite nanocrystals[J]. 中国化学工程学报, 2023, 59(7): 32-41.
[3]	Wenting Fan, Fang Zhao, Ming Chen, Jian Li, Xuhong Guo. An efficient microreactor with continuous serially connected micromixers for the synthesis of superparamagnetic magnetite nanoparticles[J]. 中国化学工程学报, 2023, 59(7): 85-91.
[4]	Abdelgadir Bashir Banaga, Yan-Bin Li, Zhi-Hao Li, Bao-Chang Sun, Guang-Wen Chu. Experimental investigation of the mixing efficiency via intensity of segregation along axial direction of a rotating bar reactor[J]. 中国化学工程学报, 2023, 59(7): 153-159.
[5]	Jian Han, Xinhua Liu, Shanwei Hu, Nan Zhang, Jingjing Wang, Bin Liang. Optimization of decoupling combustion characteristics of coal briquettes and biomass pellets in household stoves[J]. 中国化学工程学报, 2023, 59(7): 182-192.
[6]	Junhao Wang, Shugang Ma, Peng Chen, Zhipeng Li, Zhengming Gao, J. J. Derksen. Mixing of miscible shear-thinning fluids in a lid-driven cavity[J]. 中国化学工程学报, 2023, 58(6): 112-123.
[7]	Jiajia Chen, Xinyu Lu, Dandan Wang, Pengcheng Xiu, Xiaoli Gu. Effective depolymerization of alkali lignin using an attapulgite-Ce_0.75Zr_0.25O₂(ATP-CZO)-supported cobalt catalyst in ethanol/isopropanol media[J]. 中国化学工程学报, 2023, 57(5): 50-62.
[8]	Shengfeng Luo, Song Zhang, Yiping Zeng, Hui Zhang, Lili Zheng, Zhaopeng Xu. Study on oxygen transport and titanium oxidation in coating cracks under parallel gas flow based on LBM modelling[J]. 中国化学工程学报, 2023, 56(4): 15-24.
[9]	Jikai Dong, Bing Wang, Xinjie Wang, Chenxi Cao, Shikuan Chen, Wenli Du. Optimization of sensor deployment sequences for hazardous gas leakage monitoring and source term estimation[J]. 中国化学工程学报, 2023, 56(4): 169-179.
[10]	Shuangfei Zhao, Yingying Nie, Wenyan Zhang, Runze Hu, Lianzhu Sheng, Wei He, Ning Zhu, Yuguang Li, Dong Ji, Kai Guo. Microfluidic field strategy for enhancement and scale up of liquid–liquid homogeneous chemical processes by optimization of 3D spiral baffle structure[J]. 中国化学工程学报, 2023, 56(4): 255-265.
[11]	Tian Zhang, Qingshan Huang, Shujun Geng, Aqiang Chen, Yan Liu, Haidong Zhang. Impacts of solid physical properties on the performances of a slurry external airlift loop reactor integrating mixing and separation[J]. 中国化学工程学报, 2023, 55(3): 1-12.
[12]	Songsong Wang, Hong Li, Changyuan Tao, Renlong Liu, Yundong Wang, Zuohua Liu. Study on cavern evolution and performance of three mixers in agitation of yield-pseudoplastic fluids[J]. 中国化学工程学报, 2023, 55(3): 111-122.
[13]	Xibao Zhang, Zhenghong Luo. Bubble size modeling approach for the simulation of bubble columns[J]. 中国化学工程学报, 2023, 53(1): 194-200.
[14]	Liying Chen, Junheng Guo, Wenpeng Li, Shuchun Zhao, Wei Li, Jinli Zhang. A numerical study of mixing intensification for highly viscous fluids in multistage rotor–stator mixers[J]. 中国化学工程学报, 2022, 47(7): 218-230.
[15]	Pan Zhang, Guanghui Chen, Weiwen Wang, Guodong Zhang, Huaming Wang. Analysis of the nutation and precession of the vortex core and the influence of operating parameters in a cyclone separator[J]. 中国化学工程学报, 2022, 46(6): 1-10.