Parametric study of droplet size in an axisymmetric flow-focusing capillary device

doi:10.1016/j.cjche.2019.12.026

中国化学工程学报 ›› 2020, Vol. 28 ›› Issue (4): 1016-1022.DOI: 10.1016/j.cjche.2019.12.026

• Fluid Dynamics and Transport Phenomena • 上一篇下一篇

Parametric study of droplet size in an axisymmetric flow-focusing capillary device

Mostafa Rahimi¹, Sajad Yazdanparast², Pouya Rezai²

1 Department of Mechanical Engineering, University of Mohaghegh Ardabili, Ardabil, Iran;
2 Department of Mechanical Engineering, York University, Toronto, ON, Canada

收稿日期:2019-08-02 修回日期:2019-11-02 出版日期:2020-04-28 发布日期:2020-07-27
通讯作者: Mostafa Rahimi
基金资助:
This project has received funding support from the Natural Sciences and Engineering Research Council of Canada (NSERC) to PR.

Parametric study of droplet size in an axisymmetric flow-focusing capillary device

Mostafa Rahimi¹, Sajad Yazdanparast², Pouya Rezai²

1 Department of Mechanical Engineering, University of Mohaghegh Ardabili, Ardabil, Iran;
2 Department of Mechanical Engineering, York University, Toronto, ON, Canada

Received:2019-08-02 Revised:2019-11-02 Online:2020-04-28 Published:2020-07-27
Contact: Mostafa Rahimi
Supported by:
This project has received funding support from the Natural Sciences and Engineering Research Council of Canada (NSERC) to PR.

摘要/Abstract

摘要： A conventional technique for microfluidic droplet generation is Co-axial Flow Focusing (CFF) in which a contraction zone is placed downstream of the dispersed phase nozzle. In this contraction zone, the dispersed-phase (dphase) fluid is pinched off by continuous-phase (c-phase) fluid to generate micro-droplets. Studying the influence of multiple parameters such as the fluids velocities and viscosities, the interfacial tension, and nozzle and orifice diameters on the droplet size is of great importance for the design and application of CFF devices. Thus, development of more complete numerical models is required. In this paper, we show our model is compatible with experimental data and then numerically investigate the effects of aforementioned parameters on the droplet generation in a CFF microfluidic device. Simulation results showed that the c-phase flow rate, viscosity and the interfacial tension had great impacts on the droplet size. The effect of the nozzle diameter on the generated droplet size was small compared to that of the orifice in a CFF device. Using the simulation results, a correlation was also developed and suggested which predicts the droplet size with less than 15% error in a wide range of the introduced dimensionless parameters.

关键词: Co-axial Flow Focusing, Microfluidics, Droplet generation, Numerical investigation

Abstract: A conventional technique for microfluidic droplet generation is Co-axial Flow Focusing (CFF) in which a contraction zone is placed downstream of the dispersed phase nozzle. In this contraction zone, the dispersed-phase (dphase) fluid is pinched off by continuous-phase (c-phase) fluid to generate micro-droplets. Studying the influence of multiple parameters such as the fluids velocities and viscosities, the interfacial tension, and nozzle and orifice diameters on the droplet size is of great importance for the design and application of CFF devices. Thus, development of more complete numerical models is required. In this paper, we show our model is compatible with experimental data and then numerically investigate the effects of aforementioned parameters on the droplet generation in a CFF microfluidic device. Simulation results showed that the c-phase flow rate, viscosity and the interfacial tension had great impacts on the droplet size. The effect of the nozzle diameter on the generated droplet size was small compared to that of the orifice in a CFF device. Using the simulation results, a correlation was also developed and suggested which predicts the droplet size with less than 15% error in a wide range of the introduced dimensionless parameters.

Key words: Co-axial Flow Focusing, Microfluidics, Droplet generation, Numerical investigation

Mostafa Rahimi, Sajad Yazdanparast, Pouya Rezai. Parametric study of droplet size in an axisymmetric flow-focusing capillary device[J]. 中国化学工程学报, 2020, 28(4): 1016-1022.

Mostafa Rahimi, Sajad Yazdanparast, Pouya Rezai. Parametric study of droplet size in an axisymmetric flow-focusing capillary device[J]. Chinese Journal of Chemical Engineering, 2020, 28(4): 1016-1022.

参考文献

[1] S. Mashaghi, A. Abbaspourrad, D.A. Weitz, A.M. van Oijen, Droplet microfluidics:a tool for biology, chemistry and nanotechnology, TrAC Trends Anal. Chem. 82(2016) 118-125.
[2] H.C. Shum, A. Bandyopadhyay, S. Bose, D.A. Weitz, Double emulsion droplets as microreactors for synthesis of mesoporous hydroxyapatite, Chem. Mater. 21(2009) 5548-5555.
[3] P. Sanguansri, M.A. Augustin, Nanoscale materials development-a food industry perspective, Trends Food Sci. Technol. 17(2006) 547-556.
[4] Z.M. Liu, Y. Yang, Y. Du, Y. Pang, Advances in droplet-based microfluidic technology and its applications, Chin. J. Anal. Chem. 45(2017) 282-296.
[5] V. Cristini, Y.C. Tan, Theory and numerical simulation of droplet dynamics in complex flows-a review, Lab Chip 4(2004) 257-264.
[6] Y. Zhu, Q. Fang, Analytical detection techniques for droplet microfluidics-a review, Anal. Chim. Acta 787(2013) 24-35.
[7] P. Zhu, L. Wang, Passive and active droplet generation with microfluidics:a review, Lab Chip 17(2017) 34-75.
[8] J.H. Xu, S.W. Li, J. Tan, Y.J. Wang, G.S. Luo, Preparation of highly monodisperse droplet in a T-junction microfluidic device, AICHE J. 52(2006) 3005-3010.
[9] L.Y. Wu, Y.P. Chen, Visualization study of emulsion droplet formation in a coflowing microchannel, Chem. Eng. Process. 85(2014) 77-85.
[10] W.L. Ong, J. Hua, B. Zhang, T.Y. Teo, J. Zhuo, N.T. Nguyen, N. Ranganathan, L. Yobas, Experimental and computational analysis of droplet formation in a high-performance flow-focusing geometry, Sensors Actuators A 138(2007) 203-212.
[11] S.K. Moon, I.W. Cheong, S.W. Choi, Effect of flow rates of the continuous phase on droplet size in dripping and jetting regimes in a simple fluidic device for coaxial flow, Colloids Surf. A Physicochem. Eng. Asp. 454(2014) 84-88.
[12] C. Cramer, P. Fischer, E.J. Windhab, Drop formation in a co-flowing ambient fluid, Chem. Eng. Sci. 59(2004) 3045-3058.
[13] A.S. Utada, A. Fernandez-Nieves, H.A. Stone, D.A. Weitz, Dripping to jetting transition in coflowing liquid streams, Phys. Rev. Lett. 99(2007)094502.
[14] X.G. Zhang, Dynamics of drop formation in viscous flows, Chem. Eng. Sci. 12(1999) 1759-1774.
[15] T. Alkayyali, T. Cameron, B. Haltli, R.G. Kerr, A. Ahmadi, Microfluidic and crosslinking methods for encapsulation of living cells and bacteria-a review, Anal. Chim. Acta 1053(2019) 1-21.
[16] Y.C. Tan, V. Cristini, A.P. Lee, Monodispersed microfluidic droplet generation by shear focusing microfluidic device, Sensors Actuators B 114(2006) 350-356.
[17] J. Wacker, V.K. Parashar, M.A.M. Gijs, Influence of oil type and viscosity on droplet size in a flow focusing microfluidic device, Proc. Chem. 1(2009) 1083-1086.
[18] S. Kole, P. Bikkina, A parametric study on the application of microfluidics for emulsion characterization, J. Pet. Sci. Eng. 158(2017) 152-159.
[19] A. Letícia, R. Costa, A. Gomes, R. Lopes Cunha, Studies of droplets formation regime and actual flow rate of liquid-liquid flows in flow-focusing microfluidic devices, Exp. Thermal Fluid Sci. 85(2017) 167-175.
[20] P. Wu, Z. Luo, Z. Liu, Z. Li, C. Chen, L. Feng, L. He, Drag-induced breakup mechanism for droplet generation in dripping within flow focusing microfluidics, Chin. J. Chem. Eng. 23(2015) 7-14.
[21] L. Wu, X. Liu, Y. Zhao, Y. Chen, Role of local geometry on droplet formation in axisymmetric microfluidics, Chem. Eng. Sci. 163(2017) 56-67.
[22] Y. Pang, Y. Du, J. Wang, Z. Liu, Generation of single/double Janus emulsion droplets in co-flowing microtube, Int. J. Multiphase Flow 113(2019) 199-207.
[23] C. Yu, L. Wu, L. Lia, M. Liu, Experimental study of double emulsion formation behaviors in a one-step axisymmetric flow-focusing device, Exp. Thermal Fluid Sci. 103(2019) 18-28.
[24] M. Rahimi, A. Shams Korrami, P. Rezai, Effect of device geometry on droplet size in co-axial flow-focusing microfluidic droplet generation devices, Colloids Surf. A Physicochem. Eng. Asp. 570(2019) 510-517.
[25] J. Li, Y.Y. Renardy, M. Renardy, Numerical simulation of breakup of a viscous drop in simple shear flow through a volume-of-fluid method, Phys. Fluids 12(2000) 269-282.
[26] Y. Kitamura, K. Kizu, T. Takahashi, Relatively low-concentrated O/W emulsion jets, Can. J. Chem. Eng. 63(1985) 244-249.
[27] A.G. Gaonkar, Interracial tensions of vegetable oil/water systems:effect of oil purification, J. Am. Oil Chem. Soc. 66(1989) 1090-1092.
[28] O. Fasina, Z. Colley, Viscosity and specific heat of vegetable oils as a function of temperature:35℃ to 180℃, Int. J. Food Prop. 11(2008) 738-746.
[29] C.A. Schneider, W.S. Rasband, K.W. Eliceiri, NIH Image to ImageJ:25 years of image analysis, Nat. Methods 9(2012) 671-675.
[30] A. Shams Khorrami, P. Rezai, Oscillating dispersed-phase co-flow microfluidic droplet generation:multi-droplet size effect, Biomicrofluidics. 12(2018), 034113.
[31] A. Shams Khorrami, P. Rezai, Oscillating dispersed-phase co-flow microfluidic droplet generation:jet length reduction effectitle, Soft Matter 14(48) (2018) 9870-9876.

Parametric study of droplet size in an axisymmetric flow-focusing capillary device

Parametric study of droplet size in an axisymmetric flow-focusing capillary device

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics

本文评价

[1]	Qingming Ma, Jianhong Xu. Green microfluidics in microchemical engineering for carbon neutrality[J]. 中国化学工程学报, 2023, 53(1): 332-345.
[2]	Fang Yang, Wei Zhao, Guiren Wang. Electrokinetic mixing of two fluids with equivalent conductivity[J]. 中国化学工程学报, 2022, 42(2): 256-260.
[3]	Zifei Yan, Jiaxin Tian, Chencan Du, Jian Deng, Guangsheng Luo. Reaction kinetics determination based on microfluidic technology[J]. 中国化学工程学报, 2022, 41(1): 49-72.
[4]	Yifan Xing, Junyu Liu, Xiaojie Guo, Haipeng Liu, Wen Zeng, Yi Wang, Chong Zhang, Yuan Lu, Dong He, Shaohua Ma, Yonghong He, Xin-Hui Xing. Engineering organoid microfluidic system for biomedical and health engineering: A review[J]. 中国化学工程学报, 2021, 29(2): 244-254.
[5]	Xuanyu Li, Qiang Feng, Ziwei Han, Xingyu Jiang. Enhancing gene editing efficiency for cells by CRISPR/Cas9 system-loaded multilayered nanoparticles assembled via microfluidics[J]. 中国化学工程学报, 2021, 38(10): 216-220.
[6]	Wenhao Niu, Yuanzhi Zheng, Ying Li, Le Du, Wei Liu. Photochemical microfluidic synthesis of vitamin D₃ by improved light sources with photoluminescent substrates[J]. 中国化学工程学报, 2021, 29(1): 204-211.
[7]	Shaobin Zhang, Helen Yan, Yuhao Geng, Ke Wang, Jianhong Xu. Equilibrium morphology of gas-liquid Janus droplets: A numerical analysis of buoyancy effect[J]. Chinese Journal of Chemical Engineering, 2018, 26(10): 2121-2126.
[8]	Yunlong Zhou, He Chang, Tianyu Qi. Gas-liquid two-phase flow in serpentine microchannel with different wall wettability[J]. , 2017, 25(7): 874-881.
[9]	Xuehui Ge, Hong Zhao, TaoWang, Jian Chen, Jianhong Xu, Guangsheng Luo. Microfluidic technology for multiphase emulsions morphology adjustment and functional materials preparation[J]. Chinese Journal of Chemical Engineering, 2016, 24(6): 677-692.
[10]	Ping Wu, Zhaofeng Luo, Zhifeng Liu, Zida Li, Chi Chen, Lili Feng, Liqun He. Drag-induced breakup mechanism for droplet generation in dripping within flow focusing microfluidics[J]. Chinese Journal of Chemical Engineering, 2015, 23(1): 7-14.
[11]	Elmabruk A. Mansur, 叶明星, 王运东, 戴猷元. A State-of-the-Art Review of Mixing in Microfluidic Mixers[J]. , 2008, 16(4): 503-516.