Discharge characteristics of coal and extraction residue from direct coal liquefaction in partial fluidization silo

doi:10.1016/j.cjche.2021.12.002

中国化学工程学报 ›› 2022, Vol. 52 ›› Issue (12): 78-87.DOI: 10.1016/j.cjche.2021.12.002

• Full Length Article • 上一篇下一篇

Discharge characteristics of coal and extraction residue from direct coal liquefaction in partial fluidization silo

Zhen Liu^1,2, Haiquan An², Jiansheng Zhang¹

1. Department of Energy and Power Engineering, Tsinghua University, Beijing 100084, China;
2. National Institute of Clean-and-Low-Carbon Energy, Beijing 100084, China

收稿日期:2021-07-18 修回日期:2021-11-29 出版日期:2022-12-28 发布日期:2023-01-31
通讯作者: Jiansheng Zhang,E-mail:zhang-jsh@tsinghua.edu.cn
基金资助:
The authors would like to express their gratitude to Edit Springs (https://www.editsprings.com/) for the expert linguistic services provided.

Discharge characteristics of coal and extraction residue from direct coal liquefaction in partial fluidization silo

Zhen Liu^1,2, Haiquan An², Jiansheng Zhang¹

1. Department of Energy and Power Engineering, Tsinghua University, Beijing 100084, China;
2. National Institute of Clean-and-Low-Carbon Energy, Beijing 100084, China

Received:2021-07-18 Revised:2021-11-29 Online:2022-12-28 Published:2023-01-31
Contact: Jiansheng Zhang,E-mail:zhang-jsh@tsinghua.edu.cn
Supported by:
The authors would like to express their gratitude to Edit Springs (https://www.editsprings.com/) for the expert linguistic services provided.

摘要/Abstract

摘要： Gasification of extraction residue (ER) from direct coal liquefaction with pulverized coal is an efficient way for the utilization of carbonaceous wastes, which improve the overall efficiency of direct coal liquefaction technology. The discharge characteristics of ER mixing with pulverized coal is important paraments for its gasification process, which is seldom studied in the literature. In this study, the discharge characteristics of the pulverized coal (M1) as well as its mixture with ER (M2) were systematically investigated in an atmospheric pressure partial fluidization silo with different fluidization apparent velocity. It was observed that although M2 is a viscous powder with lower flowability than M1, the mass flow rate of M2 is 65% higher than M1 at the 3.7 mm·s^-1 apparent gas velocity. M2 exhibits the properties of Geldart A type powder, which improves the mass flow rate and stability of the discharged material. The mass flow rate of both M1 and M2 first increases and then slowly decreases with the increase of apparent gas velocity of the fluidizing air, which means the discharge process of M1 and M2 can be optimized by the apparent gas velocity.

关键词: Discharge characteristics, Silo, Extraction residue, Direct coal liquefaction, Fluidizing air

Abstract: Gasification of extraction residue (ER) from direct coal liquefaction with pulverized coal is an efficient way for the utilization of carbonaceous wastes, which improve the overall efficiency of direct coal liquefaction technology. The discharge characteristics of ER mixing with pulverized coal is important paraments for its gasification process, which is seldom studied in the literature. In this study, the discharge characteristics of the pulverized coal (M1) as well as its mixture with ER (M2) were systematically investigated in an atmospheric pressure partial fluidization silo with different fluidization apparent velocity. It was observed that although M2 is a viscous powder with lower flowability than M1, the mass flow rate of M2 is 65% higher than M1 at the 3.7 mm·s^-1 apparent gas velocity. M2 exhibits the properties of Geldart A type powder, which improves the mass flow rate and stability of the discharged material. The mass flow rate of both M1 and M2 first increases and then slowly decreases with the increase of apparent gas velocity of the fluidizing air, which means the discharge process of M1 and M2 can be optimized by the apparent gas velocity.

Key words: Discharge characteristics, Silo, Extraction residue, Direct coal liquefaction, Fluidizing air

Zhen Liu, Haiquan An, Jiansheng Zhang. Discharge characteristics of coal and extraction residue from direct coal liquefaction in partial fluidization silo[J]. 中国化学工程学报, 2022, 52(12): 78-87.

Zhen Liu, Haiquan An, Jiansheng Zhang. Discharge characteristics of coal and extraction residue from direct coal liquefaction in partial fluidization silo[J]. Chinese Journal of Chemical Engineering, 2022, 52(12): 78-87.

参考文献

[1] H.Q. An, J. Yu, J.J. Fan, Y.C. Jiang, Z.X. Zhang, Experiment study on entrained flow gasification technology with dry slag by second-stage water supply, Powder Technol. 306 (2017) 10–16
[2] H.F. Lu, X.L. Guo, P. Li, K. Liu, X. Gong, Design optimization of a Venturi tube geometry in dense-phase pneumatic conveying of pulverized coal for entrained-flow gasification, Chem. Eng. Res. Des. 120 (2017) 208–217
[3] L. Liao, J.H. Zheng, Y. Zhang, C.C. Li, C.Q. Yuan, Impact of torrefaction on entrained-flow gasification of pine sawdust: An experimental investigation, Fuel 289 (2021) 119919
[4] Z.R. Ba, J.T. Zhao, C. Li, J.J. Huang, Y.T. Fang, L.X. Zhang, L.H. Kong, Q.F. Wang, Developing efficient gasification technology for high-sulfur petroleum coke to hydrogen-rich syngas production, Fuel 267 (2020) 117170
[5] H.Q. An, Z. Liu, X.H. Fang, Z.Y. Feng, X.L. Duan, Kinetic study of CO₂ gasification on coal char and extraction residue char from direct coal liquefaction, Int. J. Energy Res. 45 (3) (2021) 3750–3760
[6] X.L. Guo, W.X. Lu, H.F. Lu, X.L. Cong, K. Xie, H.F. Liu, X. Gong, Pressure drop prediction for horizontal dense-phase pneumatic conveying of pulverized coal associated with feeding to gasifier, Chem. Eng. Res. Des. 91(12) (2013) 2509–2514
[7] Y. Jin, H.F. Lu, X.L. Guo, X. Gong, The effect of water addition on the surface energy, bulk and flow properties of lignite, Fuel Process.Technol. 176 (2018) 91–100
[8] Y. Jin, H.F. Lu, X.L. Guo, X. Gong, Effect of water addition on flow properties of lignite particles, Chem. Eng. Res. Des. 132 (2018) 1020–1029
[9] C.D. Spink, R.M. Nedderman, Gravity discharge rate of fine particles from hoppers, Powder Technol. 21 (2) (1978) 245–261
[10] Q. Guo, H.F. Liu, X.L. Chen, S.D. Li, X.L. Guo, X. Gong, Research on the flow properties of the blended particles of rice straw and coal, Fuel 102 (2012) 453–459
[11] J.R. Darias, D. Gella, M.E. Fernández, I. Zuriguel, D. Maza, The hopper angle role on the velocity and solid-fraction profiles at the outlet of silos, Powder Technol. 366 (2020) 488–496
[12] H.F. Lu, J.K. Cao, X.L. Guo, X. Gong, L. Fu, Design optimization of an aerated hopper for discharge of cohesive pulverized coal, Powder Technol. 357 (2019) 186–192
[13] H.F. Lu, X.L. Guo, X. Gong, D. Barletta, M. Poletto, Prediction of solid discharge rates of pulverized coal from an aerated hopper, Powder Technol. 286 (2015) 645–653
[14] H.F. Lu, X.L. Guo, X. Gong, X.L. Cong, K. Liu, H.F. Qi, Experimental study on aerated discharge of pulverized coal, Chem. Eng. Sci. 71(2012) 438–448
[15] H.J. Zhou, Y.Q. Xiong, Y. Pei, Effect of moisture content on dense-phase pneumatic conveying of pulverized lignite under high pressure, Powder Technol. 287 (2016) 355–363
[16] X.H. Fang, H.Q. An, Z. Liu, Z.Y. Feng, B.Z. Peng, Y.G. Wang, Study on characteristics of the dense phase transportation of pulverized coal pressure, Clean Coal Technol. 25 (05) (2019) 59–65. (in Chinese)
[17] P. Chen, Z.L. Yuan, X.L. Shen, Y.Y. Zhang, Flow properties of three fuel powders, Particuology 10 (4) (2012) 438–443
[18] H.Q. An, X. Wang, X.H. Fang, Z. Liu, C. Liang, Wall normal stress characteristics in an experimental coal silo, Powder Technol. 377 (2021) 657–665
[19] X. Wang, C. Liang, X.Q. Guo, Y.Y. Chen, D.Y. Liu, J.L. Ma, X.P. Chen, H.Q. An, Experimental study on the dynamic characteristics of wall normal, Powder Technol. 363 (2020) 509-518

Discharge characteristics of coal and extraction residue from direct coal liquefaction in partial fluidization silo

Discharge characteristics of coal and extraction residue from direct coal liquefaction in partial fluidization silo

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	Chuang Liang, Zhihao Liu, Baochang Sun, Haikui Zou, Guangwen Chu. Improvement in discharge characteristics and energy yield of ozone generation via configuration optimization of a coaxial dielectric barrier discharge reactor[J]. 中国化学工程学报, 2023, 60(8): 61-68.
[2]	Guorong Wu, Qiangwen Fan, Wenjie Sun, Zhiwu Yu, Zhiqian Jia, Jianguo Ma. Regulatable pervaporation performance of Zn-MOFs/polydimethylsiloxane mixed matrix pervaporation membranes[J]. 中国化学工程学报, 2022, 42(2): 312-318.
[3]	Jie Wang, Ling Zhang, Chunzhong Li. Superhydrophobic and mechanically robust polysiloxane composite coatings containing modified silica nanoparticles and PS-grafted halloysite nanotubes[J]. 中国化学工程学报, 2022, 52(12): 56-65.
[4]	Jitai Li, Chu Zhai, Hengbo Yin, Aili Wang, Lingqin Shen. Impact of polydimethylsiloxanes on physicochemical and tribological properties of naphthenic mineral oil (KN 4010)-based titanium complex grease[J]. 中国化学工程学报, 2019, 27(4): 944-948.
[5]	Yang Han, Shengnan Li, Rong Ding, Wenjin Xu, Guangxu Zhang. Baeyer–Villiger oxidation of cyclohexanone catalyzed by cordierite honeycomb washcoated with Mg–Sn–W composite oxides[J]. 中国化学工程学报, 2019, 27(3): 564-574.
[6]	Víctor X. Mendoza-Escamilla, Alejandro Alonzo-García, Helvio R. Mollinedo, Israel González-Neria, J. Antonio Yáñez-Varela, Sergio A. Martinez-Delgadillo. Assessment of k-ε models using tetrahedral grids to describe the turbulent flow field of a PBT impeller and validation through the PIV technique[J]. Chinese Journal of Chemical Engineering, 2018, 26(5): 942-956.
[7]	Yazhen Shen, Cong Zhao, Jianmin Zhou, Changwen Du . Application of waterborne acrylic emulsions in coated controlled release fertilizer using reacted layer technology[J]. Chinese Journal of Chemical Engineering, 2015, 23(1): 309-314.
[8]	张文林, 杜威, 孟楠, 孙如意, 李春利. Measurement and Correlation of Vapor-Liquid Equilibria for Hexamethyl Disiloxane + Vinyl Acetate System at 101.3 kPa[J]. Chinese Journal of Chemical Engineering, 2014, 22(2): 177-180.
[9]	林东杰, 丁忠伟, 刘丽英, 马润宇. A Method to Obtain Gas-PDMS Membrane Interaction Parameters for UNIQUAC Model[J]. Chinese Journal of Chemical Engineering, 2013, 21(5): 485-493.
[10]	刘赛男, 刘公平, 卫旺, 相里粉娟, 金万勤. Ceramic Supported PDMS and PEGDA Composite Membranes for CO₂ Separation[J]. Chinese Journal of Chemical Engineering, 2013, 21(4): 348-356.
[11]	陈建, 赵小双, 张光旭, 陈波, 蔡卫权. Synthesis of ε-Caprolactone by Oxidation of Cyclohexanone with Monoperoxysuccinic Acid[J]. Chinese Journal of Chemical Engineering, 2013, 21(12): 1404-1409.
[12]	伍艳辉, 谭惠芬, 李佟茗, 金源. Pervaporation of Aqueous Solution of Acetaldehyde Through ZSM-5 Filled PDMS Composite Membrane[J]. Chinese Journal of Chemical Engineering, 2012, 20(4): 625-632.
[13]	Krzysztof Grudzien, Zbigniew Chaniecki, Andrzej Romanowski, Maciej Niedostatkiewicz, Dominik Sankowski. ECT Image Analysis Methods for Shear Zone Measurements during Silo Discharging Process[J]. , 2012, 20(2): 337-345.
[14]	赵长伟, 李继定, 陈剑, 亓荣彬, 栾兆坤. Separation of Sulfur/Gasoline Mixture with Polydimethylsiloxane/Polyetherimide Composite Membranes by Pervaporation[J]. , 2009, 17(4): 707-710.
[15]	陈碧, 詹晓力, 易玲敏, 陈丰秋. 酸白土催化体系开环八甲基环四硅氧烷的研究及机理探讨[J]. , 2007, 15(5): 661-665.