Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22

›› 2011, Vol. 19 ›› Issue (6): 1069-1074.

• • 上一篇

Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22

韩崇刚¹, 杨卫民¹, 丁玉梅¹, 关昌峰¹, 李锋祥², 张震¹, 阎华¹

1. State Key Laboratory of Organio-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029, China;
2. Practical New-type Patent Examination Department of State Intellectual Property Office of China, Beijing 100191, China

收稿日期:2011-01-10 修回日期:2011-08-26 出版日期:2011-12-28 发布日期:2012-04-24
通讯作者: YANG Weimin, E-mail: yangwm@mail.buct.edu.cn
基金资助:
Supported by the National Natural Science Foundation of Beijing (3102023);the National Science and Technology Support Plan Project (2011BAA04B02)

Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22

HAN Chonggang¹, YANG Weimin¹, DING Yumei¹, GUAN Changfeng¹, LI Fengxiang², ZHANG Zhen¹, YAN Hua¹

1. State Key Laboratory of Organio-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029, China;
2. Practical New-type Patent Examination Department of State Intellectual Property Office of China, Beijing 100191, China

Received:2011-01-10 Revised:2011-08-26 Online:2011-12-28 Published:2012-04-24
Supported by:
Supported by the National Natural Science Foundation of Beijing (3102023);the National Science and Technology Support Plan Project (2011BAA04B02)

摘要/Abstract

摘要： The paper described experimental investigation of heat transfer and single-phase pressure drop through tubes with different rotor-assembled strands inserted in the Reynolds number range of 800-9000 with lubricant as working fluid. In the experiment, fixed mounts were employed to eliminate the entrance effect. The experimental results showed that the employment of fixed mounts led to a visible bias of friction factor in the laminar regime while it could not affect the Nusselt numbers significantly. Experiment for the tube inserted with rotors-assembled strand showed remarkable improvement for heat transfer with the Nusselt number increased by 200%-225% in the laminar regime and 125%-160% in the transitional regime. Meanwhile, the friction factor increased inevitably by 200%-300% within the same range of Reynolds number. The comparison of different rotor-assembled strands inserted tubes and plain tube showed that the heat transfer benefited from the increase of the diameter of rotor-assembled strand with the same lead and the decrease of the lead of rotor-assembled strand, so does the friction factor. Based on experimental data and thorough multivariant linear normal regression method, the correlations of average Nusselt number and friction factor are established.

关键词: heat transfer enhancement, rotor-assembled strand, friction factor, thermal performance factor

Abstract: The paper described experimental investigation of heat transfer and single-phase pressure drop through tubes with different rotor-assembled strands inserted in the Reynolds number range of 800-9000 with lubricant as working fluid. In the experiment, fixed mounts were employed to eliminate the entrance effect. The experimental results showed that the employment of fixed mounts led to a visible bias of friction factor in the laminar regime while it could not affect the Nusselt numbers significantly. Experiment for the tube inserted with rotors-assembled strand showed remarkable improvement for heat transfer with the Nusselt number increased by 200%-225% in the laminar regime and 125%-160% in the transitional regime. Meanwhile, the friction factor increased inevitably by 200%-300% within the same range of Reynolds number. The comparison of different rotor-assembled strands inserted tubes and plain tube showed that the heat transfer benefited from the increase of the diameter of rotor-assembled strand with the same lead and the decrease of the lead of rotor-assembled strand, so does the friction factor. Based on experimental data and thorough multivariant linear normal regression method, the correlations of average Nusselt number and friction factor are established.

Key words: heat transfer enhancement, rotor-assembled strand, friction factor, thermal performance factor

韩崇刚, 杨卫民, 丁玉梅, 关昌峰, 李锋祥, 张震, 阎华. Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22[J]. , 2011, 19(6): 1069-1074.

HAN Chonggang, YANG Weimin, DING Yumei, GUAN Changfeng, LI Fengxiang, ZHANG Zhen, YAN Hua. Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22[J]. , 2011, 19(6): 1069-1074.

参考文献

1 Eiamsa-ard, S., Thianpong, C., Eiamsa-ard, P., Promvonge, P., “Convective heat transfer in a circular tube with short-length twisted tape insert”, Int. Commun. Heat Mass, 36, 365-371(2009).
2 Rahimi, M., Shabanian, S.R., Alsairafi, A.A., “Experimental and CFD studies on heat transfer and friction factor characteristics of a tube equipped with modified twisted tape inserts”, Chem. Eng. Process, 48, 762-770(2009).
3 Bharadwaj, P., Khondge, A.D., Date, A.W., “Heat transfer and pressure drop in a spirally grooved tube with twisted tape insert”, Int. J. Heat Mass Transfer, 52, 1938-1944(2009).
4 Promvong, P., Eiamsa-ard, S., “Heat transfer behaviors in a tube with combined conical-ring and twisted-tape insert”, Int. Commun. Heat Mass, 34, 849-859(2007).
5 Akhavan-Behabadi, M.A., Kumar, R., Jamali, M., “Investigation on heat transfer and pressure drop during swirl flow boiling of R-134a in a horizontal tube”, Int. J. Heat Mass Transfer, 52, 1918-1927(2009).
6 Chang, S.W., Yang, T.L., Jin, S.L., “Heat transfer and pressure drop in tube with broken twisted tape insert”, Exp. Therm. Fluid Sci., 32, 489-501(2007).
7 Eiamsa-ard, S., Rattanawong, S., Promvonge, P., “Turbulent convection in round tube equipped with propeller type swirl generators”, Int. Commun. Heat Mass, 36(4), 357-364(2009).
8 Gül, H., Evin, D., “Heat transfer enhancement in circular tubes using helical swirl generator insert at the entrance”, Int. J. Therm. Sci., 46, 1297-1303(2007).
9 Sivashanmugam, P., Nagarajan, P.K., “Studies on heat transfer and friction factor characteristics of laminar flow through a circular tube fitted with right and left helical screw-tape inserts”, Exp. Therm. Fluid Sci., 32, 192-197(2007).
10 Sivashanmugam, P., Suresh, S., “Experimental studies on heat transfer and friction factor characteristics of turbulent flow through a circular tube fitted with helical screw-tape inserts”, Chem. Eng. Process, 46, 1292-1298(2007).
11 Garc a, A., Solano, J.P., Vicente, P.G.V.A., “Enhancement of laminar and transitional flow heat transfer in tubes by means of wire coil inserts”, Int. J. Heat Mass Transfer, 50, 3176-3189(2007).
12 Naphon, P., “Effect of coil-wire insert on heat transfer enhancement and pressure drop of the horizontal concentric tubes”, Int. Commun. Heat Mass, 33, 753-763(2006).
13 Tijing, L.D., Pak, B.C., Bae, B.J., Lee, D.H., “A study on heat transfer enhancement using straight and twisted internal fin inserts”, Int. Commun. Heat Mass, 33, 719-726(2006).
14 Sara, B.A., Bali, T., “An experimental study on heat transfer and pressure drop characteristics of decaying swirl flow through a circular pipe with a vortex generator”, Exp. Therm. Fluid Sci., 32, 158-165(2007).
15 Promvonge, P., “Thermal enhancement in a round tube with snail entry and coiled-wire inserts”, Int. Commun. Heat Mass, 35, 623-629(2008).
16 Yang, W.M., Ding, Y.M., Geng, L.B., Huang, W., “Rotor-assembled automatic cleaning and heat transfer enhancement device”, CN Pat., 200520127121.9(2005).
17 Xie, P.C., Li, F.X., Ding, Y.M., Yan, H., Guan, C.F., Yang, W.M., “Experimental study of heat transfer enhancement and friction loss induced by inserted rotor-assembled strand(I) Water”, Chin. J. Chem. Eng., 16(6), 849-855(2008).
18 Gnielinski, V., “New equations for heat and mass transfer in turbulent pipe and channel flows”, Int. Chem. Eng., 16(2), 359-368(1976).
19 Petukhov, B.S., “Heat transfer and friction in turbulent pipe flow with variable properties”, Advances in Heat Transfer, Cho, Y.I., Greene, G.A., eds., Academic Press, New York, 503-564(1970).
20 Manglik, R.M., Bergles, A.E., “Heat transfer and pressure drop correlations for twisted tape inserts in isothermal tubes: part I-Laminar flows”, ASME J. Heat Transfer, 115, 881-889(1993).
21 Manglik, R.M., Bergles, A.E., “Heat transfer and pressure drop correlations for twisted tape inserts in isothermal tubes. II-transition and turbulent flows”, ASME J. Heat Transfer, 115, 890-896(1993).

[1]	Feng Jiang, Di Xu, Ruijia Li, Guopeng Qi, Xiulun Li. Particle collision behavior and heat transfer performance in a Na₂SO₄ circulating fluidized bed evaporator[J]. 中国化学工程学报, 2022, 46(6): 40-52.
[2]	Chuanshuai Dong, Lin Lu, Tao Wen, Shaojie Zhang. Thermal performance assessment of self-rotating twisted tapes and Al₂O₃ nanoparticle in a circular pipe[J]. 中国化学工程学报, 2021, 32(4): 77-86.
[3]	Krunal M. Gangawane, Hakan F. Oztop. Mixed convection in the heated semi-circular lid-driven cavity for nonNewtonian power-law fluids: Effect of presence and shape of the block[J]. 中国化学工程学报, 2020, 28(5): 1225-1240.
[4]	Sajad Mir, Omid Ali Akbari, Davood Toghraie, Ghanbarali Sheikhzadeh, Ali Marzban, Saeid Mir, Pouyan Talebizadehsardari. A comprehensive study of two-phase flow and heat transfer of water/Ag nanofluid in an elliptical curved minichannel[J]. 中国化学工程学报, 2020, 28(2): 383-402.
[5]	P. Soleimani, M. Khoshvaght-Aliabadi, H. Rashidi, H. Bahmanpour. Performance enhancement of water bath heater at natural gas city gate station using twisted tubes[J]. 中国化学工程学报, 2020, 28(1): 165-179.
[6]	Lichen He, Weimin Yang, Changfeng Guan, Hua Yan, Lin Zheng, Xiahua Zuo. Experimental investigation on flow characteristics in circular tube inserted with rotor-assembled strand using PIV[J]. Chinese Journal of Chemical Engineering, 2019, 27(1): 1-9.
[7]	Yongliang Wan, Runhan Wu, Cong Qi, Gang Duan, Ruizhao Yang. Experimental study on thermo-hydraulic performances of nanofluids flowing through a corrugated tube filled with copper foam in heat exchange systems[J]. Chinese Journal of Chemical Engineering, 2018, 26(12): 2431-2440.
[8]	Weiguo Xu, Guodong Liu, Qinghong Zhang, Shuai Wang, Huilin Lu, Heping Tan. Heat transfer and friction factor of Therminol liquid phase heat transfer fluid in a ribbed tube[J]. , 2017, 25(10): 1343-1351.
[9]	Pedram Karimi Pour-Fard, Ebrahim Afshari, Masoud Ziaei-Rad, Shahed Taghian-Dehaghani. A numerical study on heat transfer enhancement and design of a heat exchanger with porous media in continuous hydrothermal flow synthesis system[J]. , 2017, 25(10): 1352-1359.
[10]	Weiguo Xu, Guodong Liu, Qinghong Zhang, Shuai Wang, Huilin Lu, Heping Tan. Heat transfer and friction factor of Therminol liquid phase heat transfer fluid in a ribbed tube[J]. , 2017, 25(10): 1343-1351.
[11]	Pedram Karimi Pour-Fard, Ebrahim Afshari, Masoud Ziaei-Rad, Shahed Taghian-Dehaghani. A numerical study on heat transfer enhancement and design of a heat exchanger with porous media in continuous hydrothermal flow synthesis system[J]. , 2017, 25(10): 1352-1359.
[12]	M. Khoshvaght-Aliabadi, M. H. Akbari, F. Hormozi. An empirical study on vortex-generator insert fitted in tubular heat exchangers with dilute Cu-water nanofluid flow[J]. Chinese Journal of Chemical Engineering, 2016, 24(6): 728-736.
[13]	Suriya Chokphoemphun, Monsak Pimsarn, Chinaruk Thianpong, Pongjet Promvonge. Thermal performance of tubular heat exchanger with multiple twisted-tape inserts[J]. Chinese Journal of Chemical Engineering, 2015, 23(5): 755-762.
[14]	Zhijia Yu, Xinghua Liu, Guozhu Kuang. Water slip flow in superhydrophobic microtubes within laminar flow region[J]. Chinese Journal of Chemical Engineering, 2015, 23(5): 763-768.
[15]	Suriya Chokphoemphun, Monsak Pimsarn, Chinaruk Thianpong, Pongjet Promvonge. Heat transfer augmentation in a circular tube with winglet vortex generators[J]. Chinese Journal of Chemical Engineering, 2015, 23(4): 605-614.

Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22

Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价