Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle

doi:10.1016/j.cjche.2025.03.002

中国化学工程学报 ›› 2025, Vol. 83 ›› Issue (7): 111-124.DOI: 10.1016/j.cjche.2025.03.002

Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle

Jin Zhao¹, Zhi Ning², Ming Lv², Xu He¹

1 School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China;
2 School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China

收稿日期:2024-12-14 修回日期:2025-02-28 接受日期:2025-03-03 出版日期:2025-07-28 发布日期:2025-07-28
通讯作者: Jin Zhao,E-mail:7520220048@bit.edu.cn;Xu He,E-mail:hhexxu@bit.edu.cn
基金资助:
This study was funded by the National Natural Science Foundation of China (52276026).

Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle

Jin Zhao¹, Zhi Ning², Ming Lv², Xu He¹

1 School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China;
2 School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China

Received:2024-12-14 Revised:2025-02-28 Accepted:2025-03-03 Online:2025-07-28 Published:2025-07-28
Contact: Jin Zhao,E-mail:7520220048@bit.edu.cn;Xu He,E-mail:hhexxu@bit.edu.cn
Supported by:
This study was funded by the National Natural Science Foundation of China (52276026).

摘要/Abstract

摘要： This study utilizes a visualization nozzle and spray experimental platform to experimentally investigate the flow focusing/blurring nozzle. It is found that the working mode of the nozzle transitions from flow focusing to flow transition and eventually to flow blurring as the gas flow rate increases or the tube hole distance decreases. Conversely, an increase in liquid flow rate only facilitates the transition from flow focusing to flow transition. Changes in the gas/liquid flow rate or tube hole distance influence the gas shear effect and the gas inertial impact effect inside the nozzle, which in turn alters the working mode. An increase in gas flow rate results in a shift of the droplet size distribution towards smaller particle sizes in the flow blurring mode, whereas an increase in liquid flow rate produces the opposite effect. Notably, the impact of the gas flow rate on these changes is more pronounced than that of the liquid flow rate.

关键词: Flow focusing/blurring nozzle, Working mode, Gaseliquid flow, Multiphase flow, Particle size distribution

Abstract: This study utilizes a visualization nozzle and spray experimental platform to experimentally investigate the flow focusing/blurring nozzle. It is found that the working mode of the nozzle transitions from flow focusing to flow transition and eventually to flow blurring as the gas flow rate increases or the tube hole distance decreases. Conversely, an increase in liquid flow rate only facilitates the transition from flow focusing to flow transition. Changes in the gas/liquid flow rate or tube hole distance influence the gas shear effect and the gas inertial impact effect inside the nozzle, which in turn alters the working mode. An increase in gas flow rate results in a shift of the droplet size distribution towards smaller particle sizes in the flow blurring mode, whereas an increase in liquid flow rate produces the opposite effect. Notably, the impact of the gas flow rate on these changes is more pronounced than that of the liquid flow rate.

Key words: Flow focusing/blurring nozzle, Working mode, Gaseliquid flow, Multiphase flow, Particle size distribution

Jin Zhao, Zhi Ning, Ming Lv, Xu He. Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle[J]. 中国化学工程学报, 2025, 83(7): 111-124.

Jin Zhao, Zhi Ning, Ming Lv, Xu He. Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle[J]. Chinese Journal of Chemical Engineering, 2025, 83(7): 111-124.

参考文献

[1] B.M. Pickett, P.F. Burnette, S.P. Wells, P.D. Sullivan, J.R. Hawk, Fire safety tests comparing synthetic jet and diesel fuels with JP-8, Fire Saf. J. 46(3) (2011) 89-95.
[2] L.F. Chen, S.R. Ding, H.Y. Liu, Y.J. Lu, Y.F. Li, A.P. Roskilly, Comparative study of combustion and emissions of kerosene (RP-3), kerosene-pentanol blends and diesel in a compression ignition engine, Appl. Energy 203(2017) 91-100.
[3] B.J. Duddy, J. Lee, M. Walluk, D. Hallbach, Conversion of a spark-ignited aircraft engine to JP-8 heavy fuel for use in unmanned aerial vehicles, SAE Int. J. Eng. 4(1) (2011) 82-93.
[4] A.M. Ganan-Calvo, Generation of steady liquid microthreads and micron-sized monodisperse sprays in gas streams, Phys. Rev. Lett. 80(2) (1998) 285-288.
[5] A.M. Ganan-Calvo, Enhanced liquid atomization: from flow-focusing to flowblurring, Appl. Phys. Lett. 86(21) (2005) 214101.
[6] S. Groom, G. Schaldach, M. Ulmer, P. Walzel, H. Berndt, Adaptation of a new pneumatic nebulizer for sample introduction in ICP spectrometry, J. Anal. At. Spectrom. 20(3) (2005) 169-175.
[7] B. Almagro, A.M. Gan~an-Calvo, M. Hidalgo, A. Canals, Behaviour of a flow focusing pneumatic nebulizer with high total dissolved solids solution on radially- and axially-viewed inductively coupled plasma atomic emission spectrometry, J. Anal. At. Spectrom. 21(10) (2006) 1072-1075.
[8] P. Marmottant, E. Villermaux, Fragmentation of stretched liquid ligaments, Phys. Fluids 16(8) (2004) 2732-2741.
[9] J. Rosell-Llompart, A.M. Ganan-Calvo, Turbulence in pneumatic flow focusing and flow blurring regimes, Phys. Rev. E - Stat. Nonlinear Soft Matter Phys. 77(3 Pt 2) (2008) 036321.
[10] R. Murugan, P.S. Kolhe, K.C. Sahu, A combined experimental and computational study of flow-blurring atomization in a twin-fluid atomizer, Eur. J. Mech. Fluids. 84(2020) 528-541.
[11] R. Murugan, S. Balusamy, P. Kolhe, Experimental study of liquid spray mode of twin fluid atomizer using optical diagnostic tool, Flow Turbul. Combust. 106(1) (2021) 261-289.
[12] R. Murugan, P.S. Kolhe, Experimental investigation into flow blurring atomization, Exp. Therm. Fluid Sci. 120(2021) 110240.
[13] C. Ates, C. Gundogdu, M. Okraschevski, N. Bürkle, R. Koch, H.J. Bauer, Characterization of flow-blurring atomization with smoothed particle hydrodynamics (SPH), Int. J. Multiphas. Flow 164(2023) 104442.
[14] B.M. Simmons, H.V. Panchasara, A.K. Agrawal, A comparison of air-blast and flow-blurring injectors using phase Doppler particle analyzer technique, in: ASME Turbo Expo 2009: power for Land, Sea, and Air, Orlando, USA, 2, 2009, pp. 981-992.
[15] B.M. Simmons, A.K. Agrawal, Flow blurring atomization for low-emission combustion of liquid biofuels, Combust. Sci. Technol. 184(5) (2012) 660-675.
[16] M.D. Bohon, B.A. Metzger, W.P. Linak, C.J. King, W.L. Roberts, Glycerol combustion and emissions, Proc. Combust. Inst. 33(2) (2011) 2717-2724.
[17] L.L. Jiang, Investigation of Atomization Mechanisms and Flame Structure of a Twin-Fluid Injector for Different Liquid Fuels, Ph.D. Thesis, University of Alabama, USA, 2014.
[18] L.L. Jiang, A.K. Agrawal, Investigation of glycerol atomization in the near-field of a flow-blurring injector using time-resolved PIV and high-speed visualization, Flow Turbul. Combust. 94(2) (2015) 323-338.
[19] R. Pongvuthithum, J. Moran, T. Sankui, The design process for a closed combustion chamber flow blurring nozzle, Distr. Generat. Alternative Energy J. 34(1) (2019) 9-31.
[20] L.B. Modesto-Lopez, A.M. Ga nan-Calvo, Visualization and size-measurement of droplets generated by Flow Blurring^® in a high-pressure environment, Aerosol Sci. Technol. 52(2) (2018) 198-208.
[21] I. Qavi, L.L. Jiang, O.S. Akinyemi, Near-field spray characterization of a highviscosity alternative jet fuel blend C-3 using a flow blurring injector, Fuel 293(2021) 120350.
[22] M.N. Nasim, I. Qavi, L.L. Jiang, Effect of varying internal geometry on the nearfield spray characteristics of a swirl burst injector, Flow Turbul. Combust. 111(2) (2023) 641-674.
[23] C. Band, A.P. Merin, V. Srinivasan, Spray characteristics of shear-thinning viscoelastic liquids downstream of a counterflow atomizer, Int. J. Heat Fluid Flow 109(2024) 109496.
[24] J. Zhao, Z. Ning, M. Lv, C.H. Sun, Experimental study on gas liquid interaction outsideflowfocusing/blurring nozzle,J. Taiwan Inst. Chem. Eng.134(2022) 104304.
[25] J. Zhao, Z. Ning, M. Lü, C.H. Sun, Study on two-phase mixing inside flow focusing/blurring nozzle by gray distribution analysis method, Appl. Sci. 11(14) (2021) 6260.
[26] J. Zhao, Z. Ning, M. Lv, C.H. Sun, Research and analysis of internal flow pattern and its influence on external spray of a flow focusing/blurring nozzle, At. Sprays 32(1) (2022) 15-48.
[27] N. Ashgriz, Handbook of Atomization and Sprays: Theory and Applications, Springer, New York, 2011.

Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle

Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	Tianle Zhang, Wenjuan Bai, Qianpeng Dong, Dianming Chu, Lianlian Wang, Yan He. Hydrodynamic analysis of carbon nanotube clusters in distributor-less conical fluidized beds with step-by-step scaling[J]. 中国化学工程学报, 2024, 67(3): 117-125.
[2]	Shidong Xue, Jingkun Han, Xi Xi, Zhong Lan, Rongfu Wen, Xuehu Ma. Coordination of distinctive pesticide adjuvants and atomization nozzles on droplet spectrum evolution for spatial drift reduction[J]. 中国化学工程学报, 2024, 66(2): 250-262.
[3]	Zhaoyuan Zhang, Yidan Shu. Simulation of fixed-bed adsorption process considering particle size distribution[J]. 中国化学工程学报, 2024, 74(10): 175-189.
[4]	Shidong Xue, Jingkun Han, Xi Xi, Junyi Zhao, Zhong Lan, Rongfu Wen, Xuehu Ma. Rapid velocity reduction and drift potential assessment of off-nozzle pesticide droplets[J]. 中国化学工程学报, 2022, 46(6): 243-254.
[5]	Yanyan Liu, Chaoqun Yao, Guangwen Chen. Gas-liquid-liquid slug flow and mass transfer in hydrophilic and hydrophobic microreactors[J]. 中国化学工程学报, 2022, 50(10): 85-94.
[6]	Qiang Zheng, Jingxuan Yang, Wenhao Lian, Baoping Zhang, Xueer Pan, Zhonglin Zhang, Xiaogang Hao, Guoqing Guan. Multi-fluid Eulerian simulation of binary particles mixing and gas-solids contacting in high solids-flux downer reactor equipped with a lateral particle feeding nozzle[J]. 中国化学工程学报, 2021, 35(7): 152-162.
[7]	Xianchao Liang, Limin He, Xiaoming Luo, Qingping Li, Yuanpeng You, Yiqiu Xu. Experimental study on sand particles accumulation, migration and separation efficiency in slug catcher[J]. 中国化学工程学报, 2021, 32(4): 134-143.
[8]	Shuaifeng Zhang, Qinghua Zhang, Jianzhuang Shang, Zaisha Mao, Chao Yang. Measurement methods of particle size distribution in emulsion polymerization[J]. 中国化学工程学报, 2021, 39(11): 1-15.
[9]	Ziqing Yuan, Ziyu Chen, Jianxin Mao, Renxian Zhou. The size effect and high activity of nanosized platinum supported catalysts for low temperature oxidation of volatile organic compounds[J]. 中国化学工程学报, 2021, 39(11): 135-143.
[10]	Xiaoxia Duan, Xin Feng, Chong Peng, Chao Yang, Zaisha Mao. Numerical simulation of micro-mixing in gas-liquid and solid-liquid stirred tanks with the coupled CFD-E-model[J]. 中国化学工程学报, 2020, 28(9): 2235-2247.
[11]	Asmaa Hadane, Lhachmi Khamar, Saad Benjelloun, Abderrahman Nounah, Mohammed Khamar. CFD investigation of the agitation in the desupersaturation during the wet-process phosphoric acid (WPPA) process[J]. 中国化学工程学报, 2020, 28(8): 2064-2074.
[12]	Xiuli Zhang, Chunhu Li, Qingjie Guo, Kelei Huang. Performance of anaerobic fluidized bed microbial fuel cell with different porous anodes[J]. 中国化学工程学报, 2020, 28(3): 846-853.
[13]	Amir Heidari. CFD simulation of impeller shape effect on quality of mixing in two-phase gas–liquid agitated vessel[J]. 中国化学工程学报, 2020, 28(11): 2733-2745.
[14]	Marek Wasilewski, Stanis?aw Anweiler, Maciej Masiukiewicz. Characterization of multiphase gas-solid flow and accuracy of turbulence models for lower stage cyclones used in suspension preheaters[J]. 中国化学工程学报, 2019, 27(7): 1618-1629.
[15]	Xin Li, Pan Zhang, Jianlong Li, Weiwen Wang, Guanghui Chen. Analysis of deformation and internal flow patterns for rising single bubbles in different liquids[J]. 中国化学工程学报, 2019, 27(4): 745-758.