Turbulent Heat Transfer and Pressure Drop in Tube Fitted with Square-cut Twisted Tape

摘要/Abstract

摘要： Heat transfer,friction factor and thermal enhancement factor characteristics of a double pipe heat exchanger fitted with square-cut twisted tapes (STT) and plain twisted tapes (PTT) are investigated experimentally using the water as working fluid.The tapes (STT and PTT) have three twist ratios(y=2.0,4.4 and 6.0) and the Reynolds number ranges from 2000 to 12000.The experimental results reveal that heat transfer rate,friction factor and thermal enhancement factor in the tube equipped with STT are significantly higher than those fitted with PTT. The additional disturbance and secondary flow in the vicinity of the tube wall generated by STT are higher compared to that induced by the PTT is referred as the reason for better performance.Over the range considered,the Nusselt number,friction factor and thermal enhancement factor in a tube with STT are respectively,1.03 to 1.14,1.05 to 1.25 and 1.02 to 1.06 times of those in tube with PTT.An empirical correlation is also formulated to match with experimental data of Nusselt number and friction factor for STT and PTT.

关键词: heat transfer enhancement, friction factor, plain twisted tape, square-cut twisted tape, secondary flow

Abstract: Heat transfer,friction factor and thermal enhancement factor characteristics of a double pipe heat exchanger fitted with square-cut twisted tapes (STT) and plain twisted tapes (PTT) are investigated experimentally using the water as working fluid.The tapes (STT and PTT) have three twist ratios(y=2.0,4.4 and 6.0) and the Reynolds number ranges from 2000 to 12000.The experimental results reveal that heat transfer rate,friction factor and thermal enhancement factor in the tube equipped with STT are significantly higher than those fitted with PTT. The additional disturbance and secondary flow in the vicinity of the tube wall generated by STT are higher compared to that induced by the PTT is referred as the reason for better performance.Over the range considered,the Nusselt number,friction factor and thermal enhancement factor in a tube with STT are respectively,1.03 to 1.14,1.05 to 1.25 and 1.02 to 1.06 times of those in tube with PTT.An empirical correlation is also formulated to match with experimental data of Nusselt number and friction factor for STT and PTT.

Key words: heat transfer enhancement, friction factor, plain twisted tape, square-cut twisted tape, secondary flow

P. Murugesan, K. Mayilsamy, S. Suresh. Turbulent Heat Transfer and Pressure Drop in Tube Fitted with Square-cut Twisted Tape[J]. , 2010, 18(4): 609-617.

参考文献

1 Webb,R. L.,Hyun Kim,N.,Principles of Enhanced Heat Transfer,2nd edition,Taylor Francis Group,UK (2005).
2 Dewan,A.,Mahanda,P.,Sumithra Raju,K.,Suresh Kumar,P.,“Review of passive heat transfer augmentation techniques”,J.Power Energy,218,509 525(2004).
3 Wang,L.,Sunden,B.,“Performance comparison of some tube inserts”,Int.Comm.Heat Mass Transfer,29,45-56 (2002).
4 Eiamsa-ard,S.,Thianpong,C.,Promvonge,P.,“Experimental investigation of heat transfer and flow friction in a circular tube fitted with regularly spaced twisted tape elements”,Int.Comm.Heat Mass Transfer,33,1225-1233(2006).
5 Eiamsa-ard,S.,Promvonge,P.,“Heat transfer characteristics in a tube fitted with helical screw tape with/with-out core-rod inserts”,Int.Comm.Heat Mass Transfer,34,176-185 (2007).
6 Eiamsa-ard,S.,Pethkool,S.,Pong,C. T.,Promvonge,P.,“Turbulent flow heat transfer and pressure loss in a double pipe heat exchanger with louvered strip inserts”,Int.Comm.Heat Mass Transfer,35,120-129(2008).
7 Naphon,P.,“Heat transfer and pressure drop in the horizontal double pipes with and with out twisted tape insert”,Int.Comm.Heat Mass transfer,33,166-175(2006).
8 Chang,S. W.,Yang T. L.,Liou,J. S.,“Heat transfer and pressure drop in a tube with broken twisted tape insert”,Exp.Therm.Fluid Sci.,32,489-501(2007). 9 Chang,S. W.,Jan,Y. J.,Liou,J. S.,“Turbulent heat transfer and pressure drop in tube fitted with serrated twisted tape”,Int.J.Thermal
Sciences, 46,506-518(2007).
10 Eiamsa-ard,S.,Wongcharee,K.,Eiamsa-ard,P.,Thianpong,C.,“Heat transfer enhancement in a tube using delta-winglet twisted tape inserts”,Applied Therm.Eng.,30,310-318 (2010).
11 Eiamsa-ard,S.,Seemawute,P.,Wongcharee,K.,“Influences of peripherally-cut twisted tape insert on heat transfer and thermal performance characteristics in a laminar and turbulent tube flows”,Exp.Therm.Fluid Sci.,34,711-719(2010).
12 Chang,S.W.,Lees,A.W.,Chang,H.T.,“Influence of spiky twisted tape insert on thermal fluid performance of tubular air-water bubbly flo ”,Int. J.Therm.Sci.,48,2341-2354(2009).
13 Chiu,Y. W.,Jang,J. Y.,“3D numerical and experimental analysis for thermal-hydraulic characteristics of air flow inside a circular tube with different tube inserts”,Applied Therm.Eng.,29,250-258(2009).
14 Promvonge,P.,Eiamsa-ard,S.,“Heat transfer behaviors in a tube with combined conical-ring and twisted-tape insert”,Int.Comm.
15 Bilen,K.,Cetin,M.,Gul,H.,Balta,T.,“The investigation of groove geometry effect on heat transfer for internally grooved tubes”,Appl.Therm.Eng.,29,753-761(2009).
16 Sivashanmugam,P.,Suresh,S.,“Experimental studies on heat transfer and friction factor characteristics of laminar flow through a circular tube fitted with helical screw-tape inserts”,Appl.Therm.Eng.,26,1990-1997(2006).
17 Sivashanmugam,P.,Suresh,S.,“Experimental studies on heat transfer and friction factor characteristics of turbulent flow through a circular tube fitted with helical screw-tape inserts”,Chem.Eng.Process,46,1292-1298(2007).
18 Sivashanmugam,P.,Suresh,S.,“Experimental studies on heat transfer and friction factor characteristics of laminar flow through a circular tube fitted with regularly spaced helical screw-tape inserts”,Exp.Therm.Fluid Sci.,31,301-308(2007).
19 Sivashanmugam,P.,Suresh,S.,“Experimental studies on heat transfer and friction factor characteristics of turbulent flow through a circular tube fitted with regularly spaced helical screw-tape inserts”,Appl.Therm.Eng.,27,1311-1319(2007).
20 Hasim,F.,Yoshida,M.,Miiyashita,H.,“Compound heat transfer enhancement by a combination of a helically ribbed tube with twisted tape insert ”,J.Chem.Eng.Japan,36,1116-1122(2003).
21 Krishna,S.R.,Pathipaka,G.,Sivashanmugam,P.,“Heat transfer and pressure drop studies in a circular tube fitted with straight full twist”,Exp.Therm.Fluid Sci.,33,431-438(2009).
22 Bharadwaj,P.,Khondge,A.D.,Date,A.W.,“Heat transfer and pressure drop in a spirally grooved tube with twisted tape insert”,Int.J.Heat Mass Transfer,52,1938-1944 (2009).
23 Eiamsa-ard,S.,Thianpong,C.,Eiamsa-ard,P.,Promvonge,P.,“Convective heat transfer heat transfer in a circular tube with short-length twisted tape insert”,Int.Comm.Heat Mass Transfer,36,365-371 (2009).
24 Eiamsa-ard,S.,Thianpong,C.,Eiamsa-ard,P.,“Turbulent heat transfer enhancement by counter/co-swirling flow in a tube fitted with twin twisted tapes”,Exp.Therm.Fluid Sci.,34,53-62 (2010).
25 Thianpong,C.,Eiamsa-ard,P.,Wongcharee,K.,Eiamsa-ard,S.,“Compound heat transfer enhancement of a dimpled tube with a twisted tape swirl generator”,Int.Comm.Heat Mass Transfer,36,698-704(2009).
26 Agarwal,S. K.,Raja Rao,M.,“Heat transfer augmentation for the flow of a viscous liquid in circular tubes using the twisted tape insert”,Int.J.Heat Mass Transfer,39,3547-3557 (1996).
27 Manglik,R.M.,Bergles,A.E.“Heat transfer and pressure drop correlations for twisted-tape inserts in isothermal tubes (II)Transition and turbulent flows”,Trans.ASME J.Heat Transfer,115,890-896 (1993).
28 Al-Fahed,S.,Chamra,L. M.,Chakroun,W.,“Pressure drop and heat transfer comparison for both micro fin tube and twisted-tape inserts in laminar flow”,Exp.Therm.Fluid Sci.,18,323-333 (1999).
29 Al-Fahed,S.,Chakroun,W.,“Effect of tube-tape clearance on hea t transfer for fully developed turbulent flow in a horizontal isothermal tube”,Int. J. Heat Fluid Flow,17,173-178(1996).
30 Tijing,L. D.,Pak,B. C.,Baek,B. J.,Lee,D. H.,“A study on heat transfer enhancement using straight and twisted internal fin inserts”, Int.Comm.Heat Mass Transfer,33,719-726 (2006).
31 Cengel,Y. A.,Heat and Mass Transfer,5th edition,McGraw-Hill,USA(2008).
32 ANSI/ASME,Measurement Uncertainty,PTC 19,Part I,1-1985(1986).
33 Dittus,F. W.,Boelter,L. M. K.,“Heat transfer in automobile radiators of the tubular type”,University of California at Berkley,Publications in Engineering,1(13),755-758(1930).Heat Mass Transfer,34,849-859(2007).

[1]	Feng Jiang, Di Xu, Ruijia Li, Guopeng Qi, Xiulun Li. Particle collision behavior and heat transfer performance in a Na₂SO₄ circulating fluidized bed evaporator[J]. 中国化学工程学报, 2022, 46(6): 40-52.
[2]	Chuanshuai Dong, Lin Lu, Tao Wen, Shaojie Zhang. Thermal performance assessment of self-rotating twisted tapes and Al₂O₃ nanoparticle in a circular pipe[J]. 中国化学工程学报, 2021, 32(4): 77-86.
[3]	Krunal M. Gangawane, Hakan F. Oztop. Mixed convection in the heated semi-circular lid-driven cavity for nonNewtonian power-law fluids: Effect of presence and shape of the block[J]. 中国化学工程学报, 2020, 28(5): 1225-1240.
[4]	Sajad Mir, Omid Ali Akbari, Davood Toghraie, Ghanbarali Sheikhzadeh, Ali Marzban, Saeid Mir, Pouyan Talebizadehsardari. A comprehensive study of two-phase flow and heat transfer of water/Ag nanofluid in an elliptical curved minichannel[J]. 中国化学工程学报, 2020, 28(2): 383-402.
[5]	P. Soleimani, M. Khoshvaght-Aliabadi, H. Rashidi, H. Bahmanpour. Performance enhancement of water bath heater at natural gas city gate station using twisted tubes[J]. 中国化学工程学报, 2020, 28(1): 165-179.
[6]	Yongliang Wan, Runhan Wu, Cong Qi, Gang Duan, Ruizhao Yang. Experimental study on thermo-hydraulic performances of nanofluids flowing through a corrugated tube filled with copper foam in heat exchange systems[J]. Chinese Journal of Chemical Engineering, 2018, 26(12): 2431-2440.
[7]	Weiguo Xu, Guodong Liu, Qinghong Zhang, Shuai Wang, Huilin Lu, Heping Tan. Heat transfer and friction factor of Therminol liquid phase heat transfer fluid in a ribbed tube[J]. , 2017, 25(10): 1343-1351.
[8]	Pedram Karimi Pour-Fard, Ebrahim Afshari, Masoud Ziaei-Rad, Shahed Taghian-Dehaghani. A numerical study on heat transfer enhancement and design of a heat exchanger with porous media in continuous hydrothermal flow synthesis system[J]. , 2017, 25(10): 1352-1359.
[9]	Weiguo Xu, Guodong Liu, Qinghong Zhang, Shuai Wang, Huilin Lu, Heping Tan. Heat transfer and friction factor of Therminol liquid phase heat transfer fluid in a ribbed tube[J]. , 2017, 25(10): 1343-1351.
[10]	Pedram Karimi Pour-Fard, Ebrahim Afshari, Masoud Ziaei-Rad, Shahed Taghian-Dehaghani. A numerical study on heat transfer enhancement and design of a heat exchanger with porous media in continuous hydrothermal flow synthesis system[J]. , 2017, 25(10): 1352-1359.
[11]	M. Khoshvaght-Aliabadi, M. H. Akbari, F. Hormozi. An empirical study on vortex-generator insert fitted in tubular heat exchangers with dilute Cu-water nanofluid flow[J]. Chinese Journal of Chemical Engineering, 2016, 24(6): 728-736.
[12]	Suriya Chokphoemphun, Monsak Pimsarn, Chinaruk Thianpong, Pongjet Promvonge. Thermal performance of tubular heat exchanger with multiple twisted-tape inserts[J]. Chinese Journal of Chemical Engineering, 2015, 23(5): 755-762.
[13]	Zhijia Yu, Xinghua Liu, Guozhu Kuang. Water slip flow in superhydrophobic microtubes within laminar flow region[J]. Chinese Journal of Chemical Engineering, 2015, 23(5): 763-768.
[14]	Suriya Chokphoemphun, Monsak Pimsarn, Chinaruk Thianpong, Pongjet Promvonge. Heat transfer augmentation in a circular tube with winglet vortex generators[J]. Chinese Journal of Chemical Engineering, 2015, 23(4): 605-614.
[15]	Watcharin Noothong, Supattarachai Suwannapan, Chinaruk Thianpong, Pongjet Promvonge. Enhanced heat transfer in a heat exchanger square-duct with discrete V-finned tape inserts[J]. , 2015, 23(3): 490-498.